Bedienungsanleitung Bosch Indego XS 300 (Seite 29 von 318) (Alle Sprachen)

764283

Zoom out

Zoom in

Vorherige Seite

1/318

Nächste Seite

English | 29

Problem Possible Cause Corrective Measure

Rough mowing conditions Select "uneven ground/low sensitivity" option from menu

item "lawn condition/bump sensor".

Flatten garden/remove/bumps/mark out unsuitable

areas with the perimeter wire – Please follow the instruc-

tions in the Installation Guide.

Grass too long Select "uneven ground/low sensitivity" option from menu

item "lawn condition/bump sensor".

Slopes in garden too steep Ensure mower only operates on slopes of 15 degrees or

less and full garden is not on a slope.

Mower gets stuck in

garden Objects/obstacles not marked out Use the perimeter wire to mark off obstacles where the

mower often gets stuck.

Newly laid turf Allow a few weeks for the soil to settle before using the

mower.

Change setting in menu item "lawn condition / bump

sensor" to low sensitivity / uneven.

After watering, wait as long as possible until you start the

mower.

Mower unintentionally

cuts flowers, etc. or

runs over certain

obstacles

Objects/obstacles below 5cm not marked

out Mark obstacle using perimeter wire leaving 30cm from

object or remove objects/obstacles.

Mower does not ap-

pear to cut logically LogiCut system depends on the garden

conditions. Mower does not necessarily

have to continue in the next uncut area.

Further information can be found on the Installation

Guide.

If behaviour re-occurs often, remap lawn area.

Mower does not always go in a straight line

when travelling between areas No corrective action needed.

Mower frequently does not find right posi-

tion or turns on the spot Change wire ID.

Wire crossed while marking an object Follow instructions in the Installation Guide.

Mower runs in random paths in an addi-

tional lawn without docking station. Normal behaviour. The LogiCut system only works in

areas with docking station.

Perimeter wire keeps

being cut Wire is not taut between pegs

Distance between pegs is more than 75cm

Make wire taut and ensure distance between pegs is

maximum 75cm. Use the wire connectors to repair the

cut. Avoid using a verticutter, scarifier, etc. over the peri-

meter wire.

Mower leaves ragged

finish/poor quality of

cut

The mower does not mow often enough Mow more frequently for a good result (e.g. by means of

more/longer slots in schedule).

Cutting blades blunt Reverse or replace cutting blades (see figure J).

Possible clogging Always turn isolator switch off first, then check under-

neath the mower. Clear out as necessary (always wear

protective gloves).

Perimeter wire not

detected No power at the docking station Check if the docking station is powered up (LED is on).

Perimeter wire damaged/cut Check perimeter wire for damage.

Wrong installation (e.g. not enough dis-

tance between wires) Follow instructions in the Installation Guide.

Perimeter wire close to a source of interfer-

ence Remove any excess (e.g. coiled up) perimeter wire

around the docking station. Change perimeter wire ID in

the menu.

Bosch Power Tools F 016 L94 037 | (11.11.2020)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch Indego XS 300 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info