Bedienungsanleitung Bosch MCM3PM386 - MultiTalent 3 Plus (Seite 23 von 204) (Alle Sprachen)

746511

Zoom out

Zoom in

Vorherige Seite

1/204

Nächste Seite

Operation

Smart tool detection (MCM3P...)

Every speed setting is identified with a differ-

ent colour (grey and red). This colour coding

system can also be found on the acces-

sories. The accessories are automatically

connected to the right speed setting.

Low speed, grey

with drive shaft

For using tools and cutting discs.

High speed, red

without drive shaft

For using the blender and universal

cutter.

Preparation

 Place the base unit on a smooth, clean

surface.

 Pull cable out of the base unit to the

required length.

Important information

– Use only the rotary switch to switch the

appliance on or off.

– Never switch the appliance off by rotating

the bowl, the blender or a tool.

– Do not switch the appliance on unless

tools or accessories have been completely

attached.

Bowl with accessories/tools

W Risk of injury from the rotating tools!

While the appliance is operating, never place

fingers in the mixing bowl. Always use the

pusher for adding ingredients. After switching

off, the drive continues running for a short

time. Change tools only when the drive is at

a standstill.

Warning!

When working with the bowl, the appliance

cannot be switched on until the bowl has

been attached and the lid has been attached

and screwed on tight.

Universal blade

for cutting, mincing, mixing.

W Risk of injury from sharp blades!

Do not touch blades of the universal blade

with bare hands. When not in use, always

store the universal blade in the blade guard.

Grip the universal blade by the edge of the

plastic handle only.

Kneading hook

for kneading dough and mixing-in

ingredients that ought not be cut (e.g. raisins

and chocolate chips).

Beating disc

for cream, egg white and

mayonnaise.

Fig. B

 Attach the bowl (arrow on bowl on dot on

the appliance .) and rotate as far as

possible in a clockwise direction (,).

 Insert tool holder into the bowl.

 Insert universal blade, whisking disc or

kneading hook into the tool holder and

release.

Note position of the tools when

inserting them! Press tools all the way

down.

Warning!

Do not add ingredients until the tools have

been inserted.

 Add ingredients.

 Attach lid with pusher (match arrow on

lid on dot on bowl .) and rotate in

a clockwise direction (,). Lid lug must be

located fully in the slot in the bowl handle.

 Insert the mains plug.

 Set the rotary switch to the desired setting.

 To add more ingredients, set the rotary

switch to P.

 Remove the pusher and add ingredients

through the feed tube. Pusher can be used

as a measuring cup.

Cutting discs

W Risk of injury from sharp blades!

Do not grip the sharp blades or edges of the

cutting discs. Grip the discs by the plastic

part in the centre only! Do not place fingers

in the feed tube. Only use the pusher when

adding more ingredients.

Slicing reversible disc –

thick/thin

for slicing fruit and vegetables.

Process at setting 1.

Identification on the reversible slicing disc:

“grob” for the thick cutting side,

“fein” for the thin cutting side

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch MCM3PM386 - MultiTalent 3 Plus Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info