Bedienungsanleitung Bosch MMBV620M (Seite 24 von 236) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

773058

Zoom out

Zoom in

Vorherige Seite

1/236

Nächste Seite

en Cleaning and maintenance

Warning!

– Do not use cleaning agents containing

alcohol or spirits.

– Do not use any sharp, pointed or metal

objects.

– Do not use abrasive cloths or cleaning

agents.

Notes:

– Clean all parts immediately after use.

This will prevent residues from drying on

and possibly attacking the plastic (e.g.

essential oils in herbs).

– When processing food such as carrots,

plastic parts may become discoloured,

but this can be removed with a few

drops of cooking oil.

In Fig. J you will find a summary of how to

clean the individual parts.

Using cleaning programme

For quick and easy precleaning.

Fit the empty blender jug onto the

appliance.

Fill with 0.25 litres of warm water and

2 drops of washing-up liquid.

Warning!

The specified quantity of 0.25 litres must

not be exceeded.

Fit the lid and press on firmly.

Close the cap and press down to the

stop.

Set the rotary selector to 0. Switch on

the appliance with button.

Press button. The symbol lights

up. The status display LEDs light up one

by one.

The appliance runs through automatic

precleaning including a brief vacuum

application phase at the start of the

programme. The programme ends

automatically.

Switch off the appliance using button.

Disconnect the mains plug.

Remove the blender jug with the lid.

Grip the vacuum seal at one end and

pull it up. Sufficient air has to get inside

the blender jug for the lid to be removed.

Rinse all parts thoroughly and clean

again if necessary.

To make cleaning the blender jug easier,

remove the cover from the handle and

replace once dry.

Clean the base unit.

Removing the blade insert

X Image sequence G

1. Remove the lid. Turn the blender jug

over.

2. Fit the lid onto the blade insert.

3. Rotate the lid anticlockwise and remove.

4. Remove the blade insert.

Removing the vacuum valve

X Image sequence H

The vacuum valve can be removed for

cleaning.

1. Rotate the vacuum valve anticlockwise

and remove.

2. Thoroughly clean the cap, the two

moisture sensors, the valve and the filter

on the valve.

3. Make sure you dry all parts thoroughly.

4. Fit valve as shown. Marking pointing

to . Rotate the valve clockwise to the

stop. Marking pointing to .

Removing the setting rings

X Image sequence I

In order to clean them thoroughly, the

setting rings in the lid of the vacuum

container can be removed.

1. Insert a small screwdriver into one of

the two recesses of the safety ring and

carefully lever out the ring by applying

slight pressure.

2. Remove the safety ring and setting rings as

shown. Thoroughly clean and dry all parts.

3. Insert the setting rings in the order

shown. Insert the safety ring by applying

slight pressure until it clicks into place.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch MMBV620M Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info