Bedienungsanleitung Bosch MS 200 (Seite 29 von 192) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

697306

Zoom out

Zoom in

Vorherige Seite

1/192

Nächste Seite

Commissioning | 29

6 720 815 257 (2014/10)MS 200

TS19 Temperature sensor at middle of cylinder 1 (transfer /

primary store system)

TS20 Temperature sensor at top of cylinder 2 (transfer system)

VS1 3-way valve for central heating backup ( )

VS2 3-way valve for cylinder 2 (solar thermal system) with valve

VS3 3-way mixer for return temperature control ( )

VS4 3-way valve for cylinder 3 (solar thermal system) with valve

WM1 Water meter

4 Commissioning

4.1 Setting the coding card

When the coding switch is in a valid position, the indicator lights up

green continuously. When the coding switch is in an invalid position or an

intermediate position, the indicator does not light up initially. It then

starts to flash red.

Heat pump

Other heat sources

1... Solar thermal system 1

3... Transfer system 3

4 ... Primary store system 4

II Sense II

III CS 200

IV HPC 400/HMC300

4.2 System and module commissioning

4.2.1 Solar system settings

1. Set the coding card.

2. Set the coding card on other modules as applicable.

3. Switch on the power supply (mains voltage) to the entire system.

When the module indicator lights up green continuously:

4. Commission and set up the user interface as described in the

accompanying installation instructions.

5. Select the installed functions in the Solar settings > Change solar

configuration menu and add them to the solar thermal system.

6. Check the settings for the solar system at the user interface and

adjust the solar parameters if required.

7. Start the solar system.

4.2.2 Settings for transfer and primary store systems

1. Set coding switch at MS 200 for the primary store system to 7, or 8

for the transfer system.

2. Set the coding card on other modules as applicable.

3. Switch on the power supply (mains voltage) to the entire system.

If the status indicators on the modules light up green continuously:

4. Commission and set up the user interface as described in the

accompanying installation instructions.

5. Select the functions installed in the Transfer settings > Change

transfer configuration menu and add to the transfer system or

adjust the primary store system in the DHW settings menu.

6. Check the system settings at the user interface and, if required,

adjust the transfer parameters or DHW system I settings.

First make all electrical connections correctly and only

then carry out the commissioning!

▶ Follow all installation instructions for all components

and assemblies in the system.

▶ Only switch on the power supply when all modules

are set up.

NOTICE: Risk of damage to system through pump failure!

▶ Fill and vent the system before switching it on so that

the pumps do not run dry.

System

Heat

appliance

Programming

unit

Coding,

module 1

Coding,

module 2

II III IV

MS 200

MS 100

MS 200

MS 100

1 A ...  –  – 1– – –

1 A ...  –  – 1– – 2

1 B ... –  – –  1– – –

1 B ... –  – –  1– – 2

1 A ... – – –  – 10 – – –

1 A ... – – –  – 10 – – 2

3... – – –  – 8– – –

4 ...  –  – – 7– – –

Table 14 Assigning the module function via coding switch

If the coding switch at the module is set to 8 or 10, do not

establish the bus connection with a heat source.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch MS 200 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info