Bedienungsanleitung Bosch Nyon Performance Line (Seite 24 von 151) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

657611

Zoom out

Zoom in

Vorherige Seite

1/151

Nächste Seite

English–8

1 270 020 XBN | (12.5.16) Bosch eBike Systems

You can also charge the on-board computer via the USB port.

Open the protective cap 9. Connect the USB port 8 of the on-

board computer via a micro USB cable with a standard USB

charger (not included in the delivery) or the USB port of a com-

puter (5 V charging voltage, max 500 mA charging current).

Note: If Nyon is shut down during charging, Nyon can only be

switched on again if the USB cable has been disconnected

(applies to 1 270 020 907 only).

If the on-board computer is removed from the holder 4, all val-

ues of the features are saved and can still be displayed.

Without recharging the Nyon battery pack, date and time will

remain up to a maximum of 6 months. When switching back

on, date and time are reset after a successful GPS fix.

Note: To achieve a maximum lifespan of the Nyon battery

pack, the Nyon battery pack should be recharged every

6months.

Switching on/shutting down the on-board computer

To switch on the on-board computer briefly press the On/Off

button 5.

To shut down the on-board computer press the On/Off but-

ton 5 for at least 1 second.

If no button is pressed after 5 minutes, Nyon goes into power

saving mode (back lighting off) and shuts down automatically

after a further 5 minutes.

Nyon reset

If, contrary to expectations, Nyon can no longer be operated,

then Nyon can be reset by simultaneously pressing the but-

tons 1, 2, 5 and 6. Carry out the reset only if absolutely nec-

essary, as various configurations may be lost.

Battery Charge-control Indicator

The battery charge level indicator r10 (s7) displays the

charge level of the eBike battery pack. The charge level of the

Nyon battery pack can be read on the display s1. The charge

level of the eBike battery pack can also be read on the LEDs on

the eBike battery pack itself.

On indicator r10, each bar of the battery pack symbol is

equivalent to a capacity of approx. 20 %:

If the on-board computer is removed from the holder 4, the

last displayed battery charge level is saved.

Setting the Assistance Level

On the operating unit 10 you can set how much the eBike

drive assists you while pedalling. The assistance level can be

changed at any time, even while cycling.

Note: For individual versions, it is possible that the assistance

level is pre-set and cannot be changed. It is also possible that

less assistance levels are available for selection than listed

here.

The following assistance levels (max.) are available:

– “OFF”: The motor assistance is switched off, and the eBike

can be moved as a normal bicycle only by pedalling. The

push assistance cannot be activated in this assistance

level.

– “ECO”: Effective assistance at maximum efficiency for

maximum cruising range

– “TOUR”: Uniform assistance, for touring with long cruising

range

– “SPORT”: Powerful assistance for sportive riding off road

as well as for urban traffic

– “TURBO”: Maximum assistance, supporting highest ca-

dence for sportive riding

To increase the assistance level, press the “+” 14 button on

the operating unit until the desired assistance level appears in

the display r5. To decrease the assistance level, press the

button“–” 13.

The requested motor output is displayed in indicator r4. The

maximum motor output depends on the selected assistance

level.

When the on-board computer is removed from the holder 4,

the last indicated assistance level is stored; the motor-output

indicator r4 remains empty.

Switching the Push-assistance mode On/Off

The push-assistance feature makes it easier to push the

eBike. The speed in this function depends on the set gear and

cannot exceed 6 km/h (max.). The lower the set gear, the low-

er the speed in the push-assistance function (at full output).

 The push-assistance function may only be used when

pushing the eBike. Danger of injury when the wheels of

the eBike do not have ground contact while using the push-

assistance function.

To activate the push-assistance function, briefly press but-

ton “WALK” on your on-board computer. After activation,

press button “+” within 3 s and keep it pressed. The eBike

drive is switched on.

The push assistance is switched off as soon as one of the fol-

lowing occurs:

– You release button “+” 14,

– The wheels of the eBike are blocked (e.g. by actuating the

brakes or impacting against an obstacle),

– The speed exceeds 6 km/h.

The eBike battery pack is fully charged.

The eBike battery pack should be recharged.

The capacity for assisting the drive has been used

up, and assistance is gently switched off. The re-

maining capacity will be provided for the bike light

and the on-board computer.

The capacity of the eBike battery pack is enough

for about 2 hours of lighting. This does not account

for other consumers (e.g. automatic gearbox,

charging external devices at the USB port).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch Nyon Performance Line Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info