657511
24
Zoom out
Zoom in
Vorherige Seite
1/92
Nächste Seite
English8
1 270 020 XBN | (12.5.16) Bosch eBike Systems
You can also charge the on-board computer via the USB port.
Open the protective cap 9. Connect the USB port 8 of the on-
board computer via a micro USB cable with a standard USB
charger (not included in the delivery) or the USB port of a com-
puter (5 V charging voltage, max 500 mA charging current).
Note: If Nyon is shut down during charging, Nyon can only be
switched on again if the USB cable has been disconnected
(applies to 1 270 020 907 only).
If the on-board computer is removed from the holder 4, all val-
ues of the features are saved and can still be displayed.
Without recharging the Nyon battery pack, date and time will
remain up to a maximum of 6 months. When switching back
on, date and time are reset after a successful GPS fix.
Note: To achieve a maximum lifespan of the Nyon battery
pack, the Nyon battery pack should be recharged every
6 months.
Switching on/shutting down the on-board computer
To switch on the on-board computer briefly press the On/Off
button 5.
To shut down the on-board computer press the On/Off but-
ton 5 for at least 1 second.
If no button is pressed after 5 minutes, Nyon goes into power
saving mode (back lighting off) and shuts down automatically
after a further 5 minutes.
Nyon reset
If, contrary to expectations, Nyon can no longer be operated,
then Nyon can be reset by simultaneously pressing the but-
tons 1, 2, 5 and 6. Carry out the reset only if absolutely nec-
essary, as various configurations may be lost.
Battery Charge-control Indicator
The battery charge level indicator r10 (s7) displays the
charge level of the eBike battery pack. The charge level of the
Nyon battery pack can be read on the display s1. The charge
level of the eBike battery pack can also be read on the LEDs on
the eBike battery pack itself.
On indicator r10, each bar of the battery pack symbol is
equivalent to a capacity of approx. 20 %:
If the on-board computer is removed from the holder 4, the
last displayed battery charge level is saved.
Setting the Assistance Level
On the operating unit 10 you can set how much the eBike
drive assists you while pedalling. The assistance level can be
changed at any time, even while cycling.
Note: For individual versions, it is possible that the assistance
level is pre-set and cannot be changed. It is also possible that
less assistance levels are available for selection than listed
here.
The following assistance levels (max.) are available:
“OFF”: The motor assistance is switched off, and the eBike
can be moved as a normal bicycle only by pedalling. The
push assistance cannot be activated in this assistance
level.
“ECO”: Effective assistance at maximum efficiency for
maximum cruising range
“TOUR”: Uniform assistance, for touring with long cruising
range
“SPORT”: Powerful assistance for sportive riding off road
as well as for urban traffic
“TURBO”: Maximum assistance, supporting highest ca-
dence for sportive riding
To increase the assistance level, press the “+” 14 button on
the operating unit until the desired assistance level appears in
the display r5. To decrease the assistance level, press the
button“–” 13.
The requested motor output is displayed in indicator r4. The
maximum motor output depends on the selected assistance
level.
When the on-board computer is removed from the holder 4,
the last indicated assistance level is stored; the motor-output
indicator r4 remains empty.
Switching the Push-assistance mode On/Off
The push-assistance feature makes it easier to push the
eBike. The speed in this function depends on the set gear and
cannot exceed 6 km/h (max.). The lower the set gear, the low-
er the speed in the push-assistance function (at full output).
The push-assistance function may only be used when
pushing the eBike. Danger of injury when the wheels of
the eBike do not have ground contact while using the push-
assistance function.
To activate the push-assistance function, briefly press but-
ton “WALK” on your on-board computer. After activation,
press button “+” within 3 s and keep it pressed. The eBike
drive is switched on.
The push assistance is switched off as soon as one of the fol-
lowing occurs:
You release button “+” 14,
The wheels of the eBike are blocked (e.g. by actuating the
brakes or impacting against an obstacle),
The speed exceeds 6 km/h.
The eBike battery pack is fully charged.
The eBike battery pack should be recharged.
The capacity for assisting the drive has been used
up, and assistance is gently switched off. The re-
maining capacity will be provided for the bike light
and the on-board computer.
The capacity of the eBike battery pack is enough
for about 2 hours of lighting. This does not account
for other consumers (e.g. automatic gearbox,
charging external devices at the USB port).
!
!
OBJ_BUCH-2616-002.book Page 8 Thursday, May 12, 2016 12:37 PM
English9
Bosch eBike Systems 1 270 020 XBN | (12.5.16)
After releasing the “+” button, the push assistance remains on
standby for another three seconds. Pressing the “+” button
again within this period will reactivate the push assistance.
Note: On some systems the push-assistance function can be
started directly by pressing the “WALK” button.
Note: The push assistance cannot be activated in the “OFF”
assistance level.
Switching bike lights on/off
In the model, in which the lighting is powered by the eBike
system, the front and rear light can be switched on and off at
the same time via the on-board computer with the button 6.
The illumination symbol s1 is displayed when the light is on.
Switching the bike light on and off has no effect on the back
lighting of the display.
eShift (optional)
eShift is the integration of automatic gear shifting systems in-
to the eBike system. You can configure the settings for the
“eShift function under “My eBike. The gear or the cadence
is displayed in the “Ride, “Fitness” and “Map & Naviga-
tion” operating modes. If the field is not displayed, the user is
informed of changes by means of an indication on the display.
eShift mode is activated by holding down the “Home” button
12. It is only possible to activate eShift mode via the operating
unit 10. You can exit “eShift mode again by repeatedly
pressing the “Home button.
eShift with NuVinci H|Sync
The optimum gear for the respective speed is automatically
set according to a pre-defined desired cadence. In manual
mode you can choose between multiple gears.
In the “Cadence Control” mode, you can use the “–” or “+”
button on the operating unit to increase or decrease the re-
quired cadence. If you hold down the “–” or “+” button, the
cadence will increase or decrease in increments of five. The
desired cadence is shown on the display.
In the “Gear Control” mode, you can use the “–” or “+” but-
ton on the operating unit to switch back and forth between
several defined transmission ratios. The engaged gear is
shown on the display.
Under “Gear calibration”, you can calibrate the continuously
variable transmission. Then follow the instructions on the dis-
play.
In the event of an error, it can also be necessary to perform
calibration when riding. Confirm the calibration here too, and
follow the instructions on the display.
eShift with SRAM DD3 Pulse
The hub gear of the SRAM DD3 Pulse works on a speed-de-
pendent basis. Regardless of which gear is engaged on the de-
railleur gears, one of the three gears of the gear hub will auto-
matically be engaged.
It is also possible to use the “–” or “+” button to shift gear
manually here. Automatic mode is activated automatically if
you press the “–” button in first gear. If you press the “–” or
“+” button in automatic mode, the mode changes back to
manual mode. In automatic mode, only “A” is ever shown in
the gear display. If the gear is shifted in automatic mode, the
gear is not shown on the display.
If you are not in automatic mode, the engaged gear will be
shown briefly on the display whenever the gear of the hub
gear is shifted.
The drive unit recognises the gear shift and briefly reduces
the motor assistance level as a result of it, which means the
gear can also be shifted at any time under load or on a hill.
If the eBike is brought to a stop from a speed of more than
10 km/h, the system may automatically shift down a gear to a
set “Starting gear”. The “Starting gear” can be set under
“My eBike”> “eShift (SRAM).
eShift with Shimano Di2
For Shimano eShift you use the Shimano control lever to shift
gears.
The gear is always displayed in the eShift field. The gear is dis-
played briefly during a gear shift only when the eShift field is
not visible (e.g. in settings).
The drive unit recognises the gear shift and briefly reduces
the motor assistance level as a result of it, which means the
gear can also be shifted at any time under load or on a hill.
If the eBike is brought to a stop from a speed of more than
10 km/h, the system may automatically shift down a gear to a
set “Starting gear”. The “Starting gear” can be set under
“My eBike”> “eShift (Shimano).
OBJ_BUCH-2616-002.book Page 9 Thursday, May 12, 2016 12:37 PM
24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

bosch-nyon

Suche zurücksetzen

  • Mein Smartphone verbindet sich problemlos mit dem örtlichen WLAN, das Nyon allerdings nicht. Meldung: Verbindung fehlgeschlagen. Warum? Was kann ich tun? Eingereicht am 31-8-2023 19:07

    Antworten Frage melden
  • wie kann ich mein Bosch Nyon hier ib Spanien tegestrieren ?
    Eingereicht am 12-8-2023 10:07

    Antworten Frage melden
  • Wie kann ich meine Touren = Aktivitäten auf dem PC nach dem Datum suchen!? Eingereicht am 10-5-2023 20:00

    Antworten Frage melden
  • Mein Nyon 3210 zeigt auf dem Display nur noch die Kilometer an sowie den Batterie stand. Es lässt sich h nicht mehr bedienen auch nicht mit Bluetooth
    ve rbinden. Eingereicht am 12-9-2022 18:31

    Antworten Frage melden
  • Hallo, in wie weit ist die getretene Wattangabe bei E-unterstützung, genau ? Eingereicht am 28-7-2022 15:07

    Antworten Frage melden
  • Kann Mein Neues Handy nicht mit Nyon 910 koppeln/ verbinden. Was tun? Eingereicht am 28-6-2022 19:01

    Antworten Frage melden
  • Ich habe auf mein Nyon Englisch,. möchte aber deutsche Sprache


    Eingereicht am 11-5-2022 19:15

    Antworten Frage melden
  • Kann man bei einem e bike Wechsel am nyon den Kilometerstand auf null setzen Eingereicht am 25-4-2022 13:19

    Antworten Frage melden
  • Hallo,
    Die stufeneinstellung für Sport ,Turbo geht nicht .
    Das E-Bike fährt nur mit Tour , der E-Motor schaltet sich dazu !
    Woran könnte das liegen?
    Danke für eine Info! Eingereicht am 23-6-2021 20:28

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Bosch Nyon wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Bosch Nyon

Bosch Nyon Bedienungsanleitung - Deutsch - 71 seiten

Bosch Nyon Bedienungsanleitung - Englisch - 65 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info