Bedienungsanleitung Bosch PBH 3000 FRE Set (Seite 18 von 112) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

708152

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

18 | English

1 609 92A 1LU | (23.5.18)

Bosch Power Tools

– Pull out the depth stop until the distance between the tip of

the drill bit and the tip of the depth stop correspond with

the desired drilling depth X.

Selecting Drill Chucks and Tools

For hammer drilling and chiselling, SDS-plus tools are re-

quired that are inserted in the SDS-plus drill chuck.

For drilling without impact in wood, metal, ceramic and plas-

tic as well as for screwdriving, tools without SDS-plus are

used (e.g., drills with cylindrical shank). For these tools, a

keyless chuck or a key type drill chuck are required.

PBH 3000-2 FRE: The SDS-plus quick change chuck

can easily

be replaced against the quick change keyless chuck

provided.

Replacing the Drill Chuck

(PBH 2800 RE/PBH 2900RE/PBH 2900 FRE/

PBH 3000 FRE Set)

To work with drilling tools without SDS-plus (e. g., drill bits

with cylindrical shank), the key type drill chuck or the keyless

chuck must be mounted.

Mounting the Key Type Drill Chuck (Accessory)

(PBH 2800 RE/PBH 2900 RE) (see figure C)

– Screw the SDS-plus adapter shank 22 into a key type drill

chuck 21. Secure the key type drill chuck 21 with the se-

curing screw 20. Please observe that the securing

screw has a left-hand thread.

Inserting the Key Type Drill Chuck or the Keyless Chuck

(see figure D)

– Clean the shank end of the adapter shank and apply a light

coat of grease.

– Insert the key type drill chuck 21 or the keyless chuck 23

with the adapter shank into the tool holder with a turning

motion until it automatically locks.

– Check the locking effect by pulling the key type drill chuck

or the keyless chuck.

Removing the Key Type Drill Chuck or the Keyless Chuck

– Push the locking sleeve 5 toward the rear and pull out the

key type drill chuck 21 or the keyless chuck 23.

Removing/Inserting the Quick Change Chuck

(PBH 3000-2 FRE)

Removing the Quick Change Chuck (see figure E)

– Grasp the lock ring of the quick change chuck 6 and pull it

firmly in the direction of the arrow. The quick change chuck

is released and can be removed toward the front.

– After removing, protect the replacement chuck against

contamination.

Inserting the Quick Change Chuck (see figure F)

– Before inserting, clean the quick change chuck and apply a

light coat of grease to the shank end.

– Grasp the SDS-plus quick change chuck 2 or the quick

change keyless chuck 1 completely with your hand. Slide

the quick change chuck with a turning motion onto the drill

chuck mounting 24 until a distinct latching noise is heard.

– The quick change chuck is automatically locked. Check the

locking effect by pulling the quick change chuck.

Changing the Tool

The dust protection cap 4 largely prevents the entry of drilling

dust into the tool holder during operation. When inserting the

tool, take care that the dust protection cap 4 is not damaged.

 A damaged dust protection cap should be changed im-

mediately. We recommend having this carried out by

an after-sales service.

Inserting SDS-plus Drilling Tools (see figure G)

The SDS-plus drill chuck allows for simple and convenient

changing of drilling tools without the use of additional tools.

– PBH 3000-2 FRE: Insert the SDS-plus quick change chuck

– Clean and lightly grease the shank end of the tool.

– Insert the tool in a twisting manner into the tool holder until

it latches itself.

– Check the latching by pulling the tool.

As a requirement of the system, the SDS-plus drilling tool can

move freely. This causes a certain radial run-out at no-load,

which has no effect on the accuracy of the drill hole, as the

drill bit centres itself upon drilling.

Removing SDS-plus Drilling Tools (see figure H)

– Push back the locking sleeve 5 and remove the tool.

Inserting Drilling Tools without SDS-plus into the Key

Type Drill Chuck (PBH 2800 RE/PBH 2900 RE)

Note: Do not use tools without SDS-plus for hammer drilling

or chiselling! Tools without SDS-plus and their drill chucks are

damaged by hammer drilling or chiselling.

– Insert the key type drill chuck 21.

– Open the key type drill chuck 21 by turning until the tool

can be inserted. Insert the tool.

– Insert the chuck key into the corresponding holes of the

key type drill chuck 21 and clamp the tool uniformly.

– Turn the mode selector switch 12 to the “drilling” position.

Removing Drilling Tools without SDS-plus from the Key

Type Drill Chuck (PBH 2800 RE/PBH 2900 RE)

– Turn the sleeve of the key type drill chuck 21 with the drill

chuck key in anticlockwise direction until the drilling tool

can be removed.

Inserting Drilling Tools without SDS-plus into the Keyless

Chuck

(PBH 2900 FRE/PBH 3000 FRE Set/PBH 3000-2 FRE)

(see figure I)

Note: Do not use tools without SDS-plus for hammer drilling

or chiselling! Tools without SDS-plus and their drill chucks are

damaged by hammer drilling or chiselling.

– PBH 2900 FRE/PBH 3000 FRE Set: Insert the keyless

chuck 23.

– PBH 3000-2 FRE: Insert the quick change keyless chuck

– Hold the rear sleeve 26 of the keyless chuck 23 and turn

the front sleeve 25 in anticlockwise direction until until the

tool can be inserted. Insert the tool.

– Tightly hold the rear sleeve of the keyless chuck 23 and

firmly turn the front sleeve clockwise by hand until the

locking action is no longer heard. This automatically locks

the drill chuck.

– Check the tight seating by pulling the tool.

OBJ_BUCH-318-007.book Page 18 Tuesday, November 10, 2015 5:05 PM

Bosch PBH 3000 FRE Set Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info