Bedienungsanleitung Bosch PBH200RE (Seite 13 von 74) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

32133

Zoom out

Zoom in

Vorherige Seite

1/74

Nächste Seite

English–3

1 609 929 F02 • (04.10) T

The SDS-plus exchangeable drill chuck can easily be

replaced on the rotary hammer with the ring gear ex-

changeable drill chuck provided.

Hammer drilling is possible only with SDS-plus tools

that are inserted in the SDS-plus exchangeable drill

chuck.

Drilling and screwdriving are also possible with tools

without SDS-plus (e.g., round shaft drills, screwdriver

bits) that are clamped in the ring gear exchangeable

drill chuck.

Removing the Exchangeable Drill Chuck

(Fig. )

■ Danger of injury! Before removing the exchangea-

ble drill chuck, always remove the tool or bit.

Grasp the locking ring 6 of the SDS-plus exchangea-

ble drill chuck and pull forcefully in the direction of the

arrow. The exchangeable drill chuck comes off.

Attaching the Exchangeable Drill Chuck

(Fig. )

Take hold of the ring gear exchangeable drill chuck

with the whole hand. Place it with a twisting motion on

the chuck holder until it can clearly be heard to latch.

The exchangeable drill chuck locks itself.

Check locking by pulling on the exchangeable drill

chuck.

Make exchanges in the reverse order in a correspond-

ing manner.

Maintenance of the Exchangeable Drill

Chucks

Keep the connecting parts free of dust. Lubrication is

not necessary.

Take care that the dust protection cap 4 is not

damaged when changing tools.

SDS-plus Tools

The SDS-plus tool is designed to be freely movable.

This causes eccentricity when the machine is off-load.

However, the drill automatically centres itself during

operation. This does not affect drilling precision.

Inserting (Fig. )

Clean and lightly oil the tool before inserting.

Insert the dust-free tool into the tool holder 3 with

twisting until it latches.

The tool locks itself. Check the locking by pulling on

the tool.

Removing (Fig. )

Pull the locking sleeve 5 to the rear (a) and hold while

removing the tool (b).

Tools without SDS-plus

Do not use tools without SDS-plus for hammer

drilling or chiselling!

PBH 160 RE/180 RE/1800 RE/200 RE

To work with tools without SDS-plus (e.g., drills with

cylindrical shafts), a drill chuck 17 with a SDS-plus

chuck shaft 18 (optional accessory) must be inserted

into the tool holder (Fig. ).

Insert the dust-free, assembled chuck into the tool

holder 3 with twisting until it latches (Fig. ).

The chuck locks itself. Check the locking by pulling on

the chuck.

Srewdriver Bits (Fig. )

For screwdriver bits, use the SDS-plus adapter 20 (op-

tional accessory).

PBH 200 FRE

Tool Insertion (Fig. )

Turn the collar of the ring gear exchangeable drill

chuck until the tool holder is opened wide enough. In-

sert the tool and clamp with the drill chuck key 21 uni-

formly in all three holes.

For screwdriver bits, insert a commercially available bit

holder. Insert the screwdriver bits into the bit holder.

Use only screwdriver bits that fit the screw heads.

Screwdriver bits may also be inserted without a bit

holder.

Tool Removal (Fig. )

To remove a tool from the ring gear exchangeable drill

chuck, turn the collar in the direction of the arrow until

the tool can be removed.

System Accessories

Refer to the Bosch Catalogue for insertion tools.

A list of accessories can be found at the end of these

instructions.

Ensure that the mains voltage is correct!

The voltage of the power source must agree with the

value given on the nameplate of the machine. Ma-

chines designated for 230 V can also be operated with

220 V.

Switching On/Off

To switch on the machine, press the on/off switch 8.

Lock the depressed on/off switch 8 by pressing the

lock-on button 7.

To switch off the machine, release the on/off switch

8 or press and then release it.

Changing the Drill Chuck

(PBH 200 FRE)

Tool Changing (Fig. C–I)

Putting into Operation

pbh160_bu_1609929F02_t.fm Seite 3 Dienstag, 5. Oktober 2004 11:25 11

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch PBH200RE Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bosch PBH200RE

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info