Bedienungsanleitung Bosch PBH220RE (Seite 11 von 70) (Englisch, Spanisch)

32137

Zoom out

Zoom in

Vorherige Seite

1/70

Nächste Seite

Take care that the dust protection cap 4 is not

damaged when changing tools.

SDS-plus Tools

The SDS-plus tool is designed to be

freely movable. This causes

eccentricity when the machine is off-

load. However, the drill automatically

centres itself during operation. This

does not affect drilling precision.

Inserting (Fig. )

Clean and lightly oil the tool before inserting.

Insert the dust-free tool into the tool holder 3 with

twisting until it latches.

The tool locks itself. Check the locking by pulling on

the tool.

Removing (Fig. )

Pull the locking sleeve 5 to the rear (a) and hold while

removing the tool (b).

Srewdriver Bits (Fig. )

For screwdriver bits, use the SDS-plus adapter 16

(optional accessory).

Tools without SDS-plus

Do not use tools without SDS-plus for hammer

drilling or chiselling!

PBH 220 RE

(Fig. )

To work with tools without SDS-plus (e.g., drills with

cylindrical shafts), a drill chuck 17 with a SDS-plus

chuck shaft 18 (optional accessory) must be inserted

into the tool holder.

(Fig. )

Insert the dust-free, assembled chuck into the tool

holder 3 with twisting until it latches.

The chuck locks itself. Check the locking by pulling on

the chuck.

PBH 240 RE

Tool Insertion (Fig. )

Hold the holding ring 19 firmly and turn the front

collar 20 until the tool holder is open wide enough.

Insert the tool, hold firmly the holding ring 19 and turn

the collar 20 in the direction of the arrow until it

latches. Then clamp the tool by continuing to turn

forcefully until ratcheting sounds can clearly be heard.

Check the seating by pulling on the tool.

Note:

After opening the tool holder to the stop, it can happen

during the subsequent closing that the functional

ratcheting sound is heard and the tool holder does not

close.

By turning the sleeve 20 opposite to the direction of

the arrow, this ratcheting sound is switched off and the

tool holder can be closed.

For screwdriver bits, insert a commercially available bit

holder. Stick the screwdriver bits into the bit holder.

Use only screwdriver bits that fit the screw heads.

Screwdriver bits may also be inserted without a bit hol-

der.

Tool Removal (Fig. )

To remove a tool from the quick clamping replacement

drill chuck, hold firmly the holder ring 19 and turn the

front collar 20 in the direction of the arrow until the

tool can be removed.

System Accessories

Refer to the Bosch Catalogue for insertion tools.

Momentary operation

Switching on: Press the on-off switch 14.

Switching off: Release the on-off switch 14.

Continuous operation

Switching on: Press the on/off switch 14 and lock

with the locking button 15 at the

same time.

Switching off: Press and release the on/off switch 14.

Tool Changing (Fig. C-I)

Putting into Operation

pbh220_bu_1609929B38_t.fm5 Seite 14 Montag, 19. April 1999 3:07 15

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch PBH220RE Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bosch PBH220RE

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info