97308
13
Zoom out
Zoom in
Vorherige Seite
1/69
Nächste Seite
English3
1 609 929 J06 • (05.07) T
Protect the unit from strong impacts and falls. Damage to the unit can
degrade the accuracy.
After a strong impact or fall, check the laser line by comparing with a
known horizontal or vertical reference line.
Transport and store the unit in the protective bag 8.
Use Alkali-Manganese batteries exclusively.
Open the battery compartment cover 5 and insert the batteries provided.
When inserting the batteries, pay attention to the correct polarisation.
Always replace all batteries at the same time. Use only batteries from a
single manufacturer and with the same capacity.
Switching on:
When switched on, the instrument immediately emits a laser beam
from the outlet opening 3. Do not direct the laser beam at persons
or animals and do not look directly into the laser beam (espe-
cially not with optical instruments).
Press the on/off switch 2 in the “ON” direction. The instrument always
starts in the crossed line mode with levelling control.
Switching off:
Press the on/off switch 2 in the “OFF” direction. The instrument is
switched off. The laser unit is locked.
Operation with Levelling Control
With levelling control, the instrument automatically compensates for une-
venness within the self-levelling range of approx. 5°. The levelling is com-
plete as soon as the laser line no longer moves. If automatic levelling is
not possible, for example when the surface on which it is standing devi-
ates more than 5° from the horizontal, a warning signal sounds and the
laser switches itself off. In this case, reposition the instrument to horizon-
tal and wait for the self-levelling to complete.
Crossed Line Operation (see Fig. )
Place the instrument on a firm horizontal surface or attach to a tri-
pod and switch on. The laser is in crossed line operation with lev-
elling control and produces a horizontal and a vertical line.
Horizontal Operation (see Fig. )
Press the measuring mode button “mode” 1 once. The laser is in
horizontal operation with levelling control and produces a horizontal
line.
Vertical Operation (see Fig. )
Press the measuring mode button “mode” 1 again or press twice
directly after switching on. The laser is in vertical operation with lev-
elling control and produces a vertical line.
Inserting/Replacing the Batteries
Putting into Operation
Measurement Functions
C
D
E
pcl1_bu_1609929J06_t.fm Seite 3 Freitag, 29. Juli 2005 9:57 09
13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

bosch-pcl-1

Suche zurücksetzen

  • Das Gerät erzeugt keinen Laserstrahl beim Einschalten mehr.
    Was kann ich tun? Eingereicht am 25-1-2017 18:32

    Antworten Frage melden
    • Batterien prüfen, Kontaktpole der Batterien mit Schleifpapier reinigen.

      Nur für die, die es können: Aufschrauben, Schalter überprüfen, ggfs erneuern. Kabel überprüfen, ob eine Lötung abgegangen ist.

      Im Zweifel zum Fachmann. Und falls noch Garantie drauf ist, einsenden. Beantwortet 12-7-2017 20:36

      Finden Sie diese Antwort hilfreich? Antwort melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Bosch PCL 1 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info