Bedienungsanleitung Bosch Performance Line - Intuvia 2015 (Seite 29 von 219) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

780250

Zoom out

Zoom in

Vorherige Seite

1/219

Nächste Seite

English–3

Bosch eBike Systems 0 276 001 SPI | (3.6.15)

Assembly

Inserting and removing the battery pack

For inserting and removing the eBike battery pack in/from the

eBike, please read and observe the battery pack operating in-

structions.

Inserting and removing the on-board computer

(see figure A)

To insert the on-board computer 3, slide it from the front into

the holder 4.

To remove the on-board computer 3, press the lock latch 15

and slide the on-board computer toward the front out of the

holder 4.

Remove the on-board computer when you park the

eBike.

It is possible to secure the on-board computer against remov-

al in the holder. To do so, remove the holder 4 from the han-

dlebar. Put the on-board computer in the holder. Screw the

locking screw 16 (thread M3, 8 mm long) from below into the

thread provided in the holder. Mount the holder back onto the

handlebar.

Checking the Speed Sensor (seefigure B)

The speed sensor 17 and its spoke magnet 18 must be

mounted in such a manner that the spoke magnet, after a turn

of the wheel, moves past the speed sensor with a clearance of

at least 5 mm, yet no more than 17 mm.

Note: If the distance between speed sensor 17 and spoke

magnet 18 is too small or too large, or if the speed sensor 17

is not properly connected, the speed indication f will fail, and

the eBike drive unit will operate in emergency mode.

In this case, loosen the screw of the spoke magnet 18 and fas-

ten the spoke magnet to the spoke in such a manner that it runs

past the mark of the speed sensor at the correct clearance. If

the speed is still not being indicated in the speed indication f

after this, please contact an authorised bicycle dealer.

Operation

Initial Operation

Requirements

The eBike system can only be activated when the following

requirements are met:

– A sufficiently charged battery pack is inserted (see battery

pack operating instructions).

– The on-board computer is properly inserted in the holder

(see “Inserting and removing the on-board computer”,

page English–3).

– The speed sensor is connected properly (see “Checking

the Speed Sensor”, page English–3).

Switching the eBike System On/Off

Options for switching on the eBike system:

– If the on-board computer is already switched on when you

insert it into the holder, then the eBike system will be

switched on automatically.

– When the on-board computer and the eBike battery pack

are inserted, briefly press the On/Off button 5 of the on-

board computer.

– When the on-board computer is inserted, press the On/Off

button of the eBike battery pack (see battery pack operat-

ing instructions).

The drive is activated as soon as you step on the pedals

(except when in the push assistance/start assistance func-

tion, see “Switching the Push/Start Aid On/Off”, page

English–5). The motor output depends on the settings of the

assistance level on the on-board computer. As soon as the

system is activated, “Performance Line/Performance

Line CX” will appear briefly on the display.

As soon as you stop pedaling when in normal operation, or as

soon as you have reached a speed of 25/45 km/h, the assis-

tance from the eBike drive is switched off. The drive is auto-

matically re-activated as soon you start pedaling again and the

speed is below 25/45 km/h.

On-board computer Intuvia

Article number 1 270 020 909

Max. charging current,

USB connection mA 500

Charging voltage,

USB connection V5

USB charging cable1) 1 270 016 360

Operating temperature °C –5...+40

Storage temperature °C –10...+50

Charging temperature °C 0...+40

Protection type2) IP 54 (dust and splash

water protected)

Weight, approx. kg 0.15

1) Not included in standard scope of delivery

2) When USB cover is closed

Bosch eBike system uses FreeRTOS (see www.freertos.org)

Bike lights*

Rated voltage V6

Power output

–Front light

–Rear light W

W8.4

0.6

* Not possible via the eBike battery pack in all country-specific versions,

depending on the statutory regulations

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch Performance Line - Intuvia 2015 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info