Bedienungsanleitung Bosch Performance Line Drive Unit 45 km-h (Seite 8 von 50) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

657517

Zoom out

Zoom in

Vorherige Seite

1/50

Nächste Seite

English–2

0 275 007 PDS | (13.4.16) Bosch eBike Systems

Assembly

Inserting and removing the battery pack

For inserting and removing the eBike battery pack in/from the

eBike, please read and observe the battery pack operating in-

structions.

Checking the Speed Sensor (see figure A)

The speed sensor 2 and its spoke magnet 3 must be mounted

in such a manner that the spoke magnet, after a turn of the

wheel, moves past the speed sensor with a clearance of at

least 5 mm, yet no more than 17 mm.

Note: If the distance between speed sensor 2 and spoke mag-

net 3 is too small or too large, or if the speed sensor 2 is not

properly connected, the speed indication will fail, and the

eBike drive unit will operate in emergency mode.

In this case, loosen the screw of the spoke magnet 3 and fas-

ten the spoke magnet to the spoke in such a manner that it

runs past the mark of the speed sensor at the correct clear-

ance. If the speed is still not being indicated in the speed indi-

cation after this, please contact an authorised bicycle dealer.

Operation

Initial Operation

Requirements

The eBike system can only be activated when the following re-

quirements are met:

– A sufficiently charged battery pack is inserted (see battery

pack operating instructions).

– The on-board computer is properly inserted in the holder

(see on-board computer operating instructions).

– The speed sensor is connected properly (see “Checking

the Speed Sensor”, page English–2).

Switching the eBike System On/Off

Options for switching on the eBike system:

– If the on-board computer is already switched on when you

insert it into the holder, then the eBike system will be

switched on automatically.

– When the on-board computer and the eBike battery pack

are inserted, briefly press the On/Off button of the on-

board computer.

– When the on-board computer is inserted, press the On/Off

button of the eBike battery pack (see battery pack operat-

ing instructions).

Once switched on, the eBike system is in the “OFF” mode. Se-

lect the desired assistance level and set off.

Note: Depending on the version, you can also start in the pre-

viously set mode.

The drive is activated as soon as you step on the pedals (ex-

cept when in the push aid feature, see “Switching the Push-

assistance mode On/Off”, page English–3). The motor out-

put depends on the settings of the assistance level on the on-

board computer.

As soon as you stop pedaling when in normal operation, or as

soon as you have reached a speed of 45 km/h, the assistance

from the eBike drive is switched off. The drive is automatically

re-activated as soon you start pedaling again and the speed is

below 45 km/h.

Options for switching off the eBike system:

– Press the On/Off button of the on-board computer.

– Switch the eBike battery pack off by its On/Off button (see

battery pack operating instructions).

– Remove the on-board computer out of its holder.

If the eBike is not moved and no button is pressed on the on-

board computer for 10 minutes, the eBike system will shut

down automatically in order to save energy.

eShift (optional)

eShift is the integration of automatic gear shifting systems in-

to the eBike system. The eShift components are electrically

connected to the drive unit by the manufacturer. The opera-

tion of automatic gear shifting systems is described in the op-

erating instructions of the on-board computer.

Setting the Assistance Level

On the on-board computer you can set how much the eBike

drive assists you while pedalling. The assistance level can be

changed at any time, even while cycling.

Note: For individual versions, it is possible that the assistance

level is pre-set and cannot be changed. It is also possible that

less assistance levels are available for selection than listed

here.

Bike lights

Voltage, approx.

2)3)

V6/12

Maximum output

–Front light

–Taillight

8.4/17.4

0.6/0.6

1) Not possible via the eBike battery pack in all country-specific

versions, depending on the statutory regulations

2) The voltage level is preset and can be changed only by the bicycle

dealer.

3) When changing the bulbs, ensure that the bulbs are compatible with

the Bosch eBike system (ask your bicycle dealer) and that the specified

voltage matches. Bulbs must be replaced only with bulbs of the same

voltage.

 Incorrectly inserted bulbs can be destroyed!

OBJ_BUCH-2822-001.book Page 2 Wednesday, April 13, 2016 4:09 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch Performance Line Drive Unit 45 km-h Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info