Bedienungsanleitung Bosch PEX 400AE (Seite 21 von 125) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

460549

Zoom out

Zoom in

Vorherige Seite

1/125

Nächste Seite

English | 21

Bosch Power Tools 2 609 004 770 | (12.11.10)

Rough Sanding

Attach a sanding sheet with coarse grain.

Apply only light pressure to the machine so that

it runs at a higher stroke rate and high material

removal is achieved.

Fine Sanding

Attach a sanding sheet with fine grain.

By lightly varying the application pressure or

changing the orbital stroke rate, the sanding

plate stroke rate can be reduced whereby the

orbital action is maintained.

With moderate pressure, move the machine in a

circular pattern or alternately in lengthwise and

crosswise directions over the workpiece. Do not

tilt the machine to avoid sanding through the

workpiece (e.g. when sanding veneer).

After finishing the working procedure, switch

the power tool off.

Polishing

For the polishing of weathered paint or buffing

out scratches (e.g., acrylic glass), the machine

can be equipped with appropriate polishing ac-

cessories such as lamb’s wool bonnet, polishing

felt or sponge (accessories).

Select a low stroke rate (setting 1–2) for polish-

ing in order to avoid excessive heating of the

surface.

Apply the polish onto a somewhat smaller sur-

face than you intend to polish. Work the polish-

ing agent in with a suitable polishing tool apply-

ing it crosswise or with circular motion and

moderate pressure.

Do not allow the polishing agent to dry out on

the surface, otherwise the surface can become

damaged. Do not subject the surface to be pol-

ished to direct sunlight.

Clean the polishing accessories regularly to en-

sure good polishing results. Wash out polishing

accessories with a mild detergent and warm wa-

ter; do not use paint thinner.

Application Table

The data in the following table are recommended

values.

The most favourable combination for working is

best determined by practical testing.

Maintenance and Service

Maintenance and Cleaning

f Before any work on the machine itself, pull

the mains plug.

f For safe and proper working, always keep

the machine and ventilation slots clean.

If the replacement of the supply cord is neces-

sary, this has to be done by Bosch or an author-

ized Bosch service agent in order to avoid a safety

hazard.

If the machine should fail despite the care taken

in manufacturing and testing procedures, repair

should be carried out by an after-sales service

centre for Bosch power tools.

In all correspondence and spare parts order,

please always include the 10-digit article

number given on the type plate of the machine.

Application

Grain Size

(course sanding/

fine sanding)

Oscillation Rate

Roughening varnish 180/240 2/3

Touching up varnish 120/240 4/5

Removing varnish 40/60 5

Softwood 40/240 5/6

Hardwood 60/240 5/6

Veneer 180/240 2–4

Aluminium 80/240 4/5

Steel 40/240 5

Derusting steel 40/120 6

Stainless steel 80/240 5

Masonry, stone 80/240 5/6

OBJ_BUCH-1336-001.book Page 21 Friday, November 12, 2010 10:16 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch PEX 400AE Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info