Bedienungsanleitung Bosch pfz 500 (Seite 12 von 60) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

382843

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

12 | English

2 609 005 663 | (26.8.11) Bosch Power Tools

Inserting the Saw Blade (see figure A)

Insert the saw blade 1 until it latches in the SDS saw blade re-

ceptacle 7.

f Check the tight seating of the saw blade. A loose saw

blade can fall out and lead to injuries.

Removing the Saw Blade (see figure B)

Push the slider for the SDS saw blade release 8 in the direc-

tion of the arrow and pull out the saw blade 1.

Dust/Chip Extraction

f Dusts from materials such as lead-containing coatings,

some wood types, minerals and metal can be harmful to

one’s health. Touching or breathing-in the dusts can cause

allergic reactions and/or lead to respiratory infections of

the user or bystanders.

Certain dusts, such as oak or beech dust, are considered

as carcinogenic, especially in connection with wood-treat-

ment additives (chromate, wood preservative). Materials

containing asbestos may only be worked by specialists.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the

materials to be worked.

f Prevent dust accumulation at the workplace. Dusts can

easily ignite.

Operation

Starting Operation

f Observe correct mains voltage! The voltage of the pow-

er source must agree with the voltage specified on the

nameplate of the machine. Power tools marked with

230 V can also be operated with 220 V.

Switching On and Off

To start the machine, first push the lock-off button for the

On/Off switch 5 and then press the On/Off switch 4 and keep

it pressed.

To switch off the machine, release the On/Off switch 4.

Controlling the Stroke Rate

Increasing or reducing the pressure on the On/Off switch 4

enables stepless stroke-rate control of the switched-on ma-

chine.

The required stroke rate is dependent on the material and the

working conditions and can be determined by a practical trial.

Reducing the stroke rate is recommended when the saw

blade engages in the material as well as when sawing plastic

and aluminium.

Working Advice

Tips

f When sawing light building materials, observe the stat-

utory provisions and the recommendations of the ma-

terial suppliers.

f Do not carry out pocket or plunge cuts with the power

tool. Danger of kickback.

Check wood, press boards, building materials, etc. for foreign

objects such as nails, screws or similar, and remove them, if

required.

When using suitable saw blades, wood with nails can also be

sawn.

Switch the machine on and guide it toward the workpiece to

be sawn. Hold the power tool firmly with both hands, position

the guide stop 2 onto the workpiece surface and saw through

the material applying uniform supporting pressure and feed.

For a quick and clean cut, move the power tool back and forth

as with a conventional hand saw (see figure C).

After finishing the working procedure, switch the power tool

off.

If the saw blade should jam, switch the machine off immedi-

ately. Widen the gap somewhat with a suitable tool and pull

out the machine.

Flush Cuts (see figure D)

Using elastic bimetal saw blades, items still attached to a wall

(e. g. projecting building elements such as water pipes, etc.)

can be sawn off flush at the wall.

f Pay attention that the saw blade always extends be-

yond the diameter of the material being worked. There

is danger of kickback.

Position the saw blade directly against the wall and apply

some lateral pressure via the tool until the footplate faces

against the wall. Switch the power tool on and saw through

the workpiece, applying constant lateral pressure.

Coolant/Lubricant

When sawing metal, coolant/lubricant should be applied

alongside cutting line because of the material heating up.

Maintenance and Service

Maintenance and Cleaning

f Before any work on the machine itself, pull the mains

plug.

f For safe and proper working, always keep the machine

and ventilation slots clean.

Clean the saw blade holder preferably with compressed air or

a soft brush. Remove the saw blade from the power tool for

this. Ensure proper operation of the saw blade holder by ap-

plying a suitable lubricant.

Heavy contamination of the machine can lead to malfunc-

tions. Therefore, do not saw materials that produce a lot of

dust from below or overhead.

If the machine should fail despite the care taken in manufac-

turing and testing procedures, repair should be carried out by

an after-sales service centre for Bosch power tools.

In all correspondence and spare parts order, please always in-

clude the 10-digit article number given on the type plate of

the machine.

After-sales Service and Customer Assistance

Our after-sales service responds to your questions concern-

ing maintenance and repair of your product as well as spare

OBJ_BUCH-105-003.book Page 12 Friday, August 26, 2011 12:42 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch pfz 500 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info