Bedienungsanleitung Bosch pfz 600 (Seite 18 von 106) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

382830

Zoom out

Zoom in

Vorherige Seite

1/106

Nächste Seite

18 | English

2 609 932 703 | (14.9.09) Bosch Power Tools

Starting Operation

f Observe correct mains voltage! The voltage

of the power source must agree with the

voltage specified on the nameplate of the

machine. Power tools marked with 230 V

can also be operated with 220 V.

Switching On and Off

To start the machine, press the On/Off switch 5

and keep it pressed.

To lock the pressed On/Off switch 5, press the

lock-on button 6.

To switch off the machine, release the On/Off

switch 5 or when it is locked with the lock-on

button 6, briefly press the On/Off switch 5 and

then release it.

Controlling/Presetting the Stroke Rate

Increasing or reducing the pressure on the

On/Off switch 5 enables stepless stroke-rate

control of the switched-on machine.

Light pressure on the On/Off switch 5 results in

a low stroke rate. Increasing the pressure also

increases the stroke rate.

When the On/Off switch 5 is locked, it is not

possible to reduce the stroke rate.

With the thumbwheel for stroke rate preselec-

tion 4, the stroke rate can be preset and

changed during operation.

The required stroke rate is dependent on the

material and the working conditions and can be

determined by a practical trial.

Reducing the stroke rate is recommended when

the saw blade engages in the material as well as

when sawing plastic and aluminium.

After longer periods of work at low stroke rate,

the machine can heat up considerably. Remove

the saw blade from the machine and allow the

machine to cool down by running it for approx.

3 minutes at maximum stroke rate.

Working Advice

Tips

f When sawing light building materials, ob-

serve the statutory provisions and the rec-

ommendations of the material suppliers.

Note: Do not cover the ventilation slots under-

neath the tool holder with the hand.

Check wood, press boards, building materials,

etc. for foreign objects such as nails, screws or

similar, and remove them, if required.

Switch the machine on and guide it toward the

workpiece. Position the footplate 2 onto the sur-

face of the work and saw through the material

applying uniform contact pressure and feed. Af-

ter completing the working procedure, switch

the machine off.

If the saw blade should jam, switch the machine

off immediately. Widen the gap somewhat with

a suitable tool and pull out the machine.

Plunge Cutting (see figures C–D)

f The plunge cutting procedure is only suita-

ble for treating soft materials such as wood,

plaster board or similar! Do not work metal

materials with the plunge cutting proce-

dure!

Use only short saw blades for plunge cutting.

Place the machine with the edge of the footplate

2 onto the workpiece and switch on. For power

tools with stroke speed control, set the maxi-

mum stroke speed. Press the power tool firmly

against the workpiece and allow the saw blade

to slowly plunge into the workpiece.

As soon as the footplate 2 fully lays on the sur-

face of the workpiece, continue sawing along-

side the desired cutting line.

OBJ_BUCH-648-003.book Page 18 Monday, September 14, 2009 10:23 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch pfz 600 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info