Bedienungsanleitung Bosch PHO 1500 (Seite 14 von 87) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch)

766890

Zoom out

Zoom in

Vorherige Seite

1/87

Nächste Seite

14 | English

Noise/vibration information

Noise emission values determined according to

EN62841‑2‑14.

Typically, the A-weighted noise level of the power tool is:

Sound pressure level 86dB(A); sound power level

97dB(A). Uncertainty K=3dB.

Wear hearing protection!

Vibration total values ah (triax vector sum) and uncertainty K

determined according to EN62841‑2‑14:

ah=4,5m/s2, K=1,5m/s2.

The vibration level and noise emission value given in these

instructions have been measured in accordance with a

standardised measuring procedure and may be used to com-

pare power tools. They may also be used for a preliminary

estimation of vibration and noise emissions.

The stated vibration level and noise emission value repres-

ent the main applications of the power tool. However, if the

power tool is used for other applications, with different ap-

plication tools or is poorly maintained, the vibration level

and noise emission value may differ. This may significantly

increase the vibration and noise emissions over the total

working period.

To estimate vibration and noise emissions accurately, the

times when the tool is switched off or when it is running but

not actually being used should also be taken into account.

This may significantly reduce vibration and noise emissions

over the total working period.

Implement additional safety measures to protect the oper-

ator from the effects of vibration, such as servicing the

power tool and application tools, keeping their hands warm,

and organising workflows correctly.

Fitting

uPull the plug out of the socket before carrying out any

work on the power tool.

Changing the tool

uTake care when changing the planer blade. Do not pick

up the planer blade by the cutting edges. You may be

injured by the sharp cutting edges.

Use only original Bosch HM/TC planer blades. The hard

metal (HM/TC) planer blade has two cutting edges and can

be turned. If both cutting edges become blunt, the planer

blade (14) needs to be changed. The HM/TC planer blade

must not be resharpened.

Removing the planer blade (see figure A)

To turn or replace the planer blade (14), turn the blade head

(11) until it is parallel to the planer base plate (9).

 Loosen the two fastening screws (13) using the hex key

(15) (approx. 1–2 turns).

 If necessary, loosen the clamping element (12) by lightly

striking it with an appropriate implement, e.g. a wooden

wedge.

 Use a piece of wood to push the planer blade (14) to the

side and out of the blade head (11).

Fitting the planer blade (see figure B)

The guide groove on the planer blade ensures a constant,

even height setting when changing or turning the blade.

If necessary, clean the knife seat in the clamping element

(12) and the planer blade (14). When fitting the planer

blade, ensure that it is securely seated in the mounting guide

of the clamping element (12) and is aligned flush with the

side edge of the planer base plate (9) at the rear. Then

tighten the two fastening screws (13) with the hex key (15).

Note: Check that the fastening screws (13) are firmly

tightened before start-up. Turn the blade head (11) by hand

and ensure that the planer blade is not brushing against any-

thing.

Dust/Chip Extraction

The dust from materials such as lead paint, some types of

wood, minerals and metal can be harmful to human health.

Touching or breathing in this dust can trigger allergic reac-

tions and/or cause respiratory illnesses in the user or in

people in the near vicinity.

Certain dusts, such as oak or beech dust, are classified as

carcinogenic, especially in conjunction with wood treatment

additives (chromate, wood preservative). Materials contain-

ing asbestos may only be machined by specialists.

– Use a dust extraction system that is suitable for the ma-

terial wherever possible.

– Provide good ventilation at the workplace.

– It is advisable to wear a P2 filter class breathing mask.

The regulations on the material being machined that apply in

the country of use must be observed.

uAvoid dust accumulation at the workplace. Dust can

easily ignite.

Clean the chip ejector (1) regularly. Clean a clogged chip

ejector using a suitable tool, e.g. a piece of wood, com-

pressed air, etc.

uDo not allow the chip ejector to come into contact with

your hands. You may be injured by rotating parts.

Always use an external dust extraction device or chip/dust

bag to guarantee optimum suction.

External dust extraction (see figure C)

An extraction hose (dia. 35 mm) (16) (accessory) can be

connected to the chip ejector on either side (PHO 2000) or

a single side only (PHO 1500).

Connect the dust extraction hose (16) to a dust extractor

(accessory). You will find an overview of how to connect

various dust extractors at the end of these operating instruc-

tions.

The dust extractor must be suitable for the material being

worked.

When extracting dry dust that is especially detrimental to

health or carcinogenic, use a special dust extractor.

Self-generated dust extraction (see figure C)

A chip/dust bag (accessory) (17) can be used for smaller

jobs. Insert the dust bag nozzle of the chip/dust bag firmly

1 609 92A 49E | (18.02.2021) Bosch Power Tools

Bosch PHO 1500 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info