Bedienungsanleitung Bosch PKP 18 E (Seite 7 von 34) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

544059

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

English | 7

Bosch Power Tools 1 609 929 460 | (26.3.12)

Product Description and Specifica-

tions

Intended Use

The glue gun is intended for the quick gluing of clean, dry and

grease-free materials with hot-melt adhesives.

Use the glue gun only when you fully understand and can per-

form all functions without limitation, or have received appro-

priate instructions.

Product Features

The numbering of the product features refers to the illustra-

tion of the glue gun on the graphics page.

1 Nozzle

2 Heat protection cover

3 Glue stick

4 Feed trigger

5 Support stand

Accessories shown or described are not part of the standard deliv-

ery scope of the product. A complete overview of accessories can

be found in our accessories program.

Technical Data

Assembly

– Screw a nozzle 1 onto the glue gun. Insert the support

stand 5 into the openings on both sides of the glue gun.

Operation

Starting Operation

f Observe the mains voltage! The voltage of the power

source must correspond with the data on the type plate of

the machine. Glue guns marked with 230 V can also be op-

erated with 220 V.

Switching On and Off (see figure A)

–To start the operation of the glue gun, insert the mains

plug into the socket outlet.

Allow the glue gun to heat up for approx. 7 minutes before be-

ginning to work. For this, position the glue gun on the support

stand 5 as shown in the figure.

–To switch off the glue gun, pull the mains plug out of the

socket outlet.

When not using the power tool, pull the mains plug in order to

save energy.

Working Advice

f For longer work breaks, pull the mains plug.

f Do not allow the hot glue or the nozzle tip to come into

contact with persons or animals. Glue and nozzle tip

reach a temperature of approx. 200 ° C; danger of burning.

If hot glue comes into contact with the skin, hold the affect-

ed area immediately under a stream of cold water for sev-

eral minutes. Do not try to remove the glue from the skin.

As the result of heat storage, the glue gun can also be used af-

ter it has heated up for a certain time after switching off. When

the glue that emerges starts to become thick, plug the mains

plug into the socket outlet again.

Preparations for Gluing

The surfaces to be glued must be clean, dry and free of

grease. Roughen smooth surfaces before gluing.

f Do not use inflammable solvents for cleaning the sur-

faces to be glued. Solvent remainders can ignite from the

hot glue, or hazardous vapours can develop.

The ambient temperature and the workpieces to be glued may

not be colder than +5 °C and warmer than +50 °C.

Warm rapidly cooling materials (e.g., steel) for better adhe-

sion using a hot air gun or similar.

Gluing (see figure B)

– Allow the glue gun to heat up. Insert the appropriate glue

stick 3 for the material being glued via the opening at the

rear. Press the feed trigger 4 applying moderate pressure.

– Apply the glue in the form of points. For gluing flexible ma-

terials (e.g., textiles), apply the glue in a zig-zag line.

– After applying the glue, immediately press the surfaces to

be glued together for approx. 30 s. The glued spot can be

subjected to load after a cool-down period of approx.

5 minutes.

– Rest the gun on the support stand 5 between individual

gluing runs.

Remove glue residue after cooling with a sharp object. If re-

quired, glued spots can be separated again by applying heat.

Glued spots can be painted.

Changing the Nozzle

–The nozzle 1 can only be changed when in warm condition.

For this, heat up the glue gun for approx. 2 minutes.

f When changing the nozzle, wear protective gloves.

Grasp the hot nozzle only by the heat protection cover

2. Danger of burning when touching the hot nozzle tip.

– Hand-tighten the new nozzle 1.

Glue Gun PKP 18 E

Article number

0 603 264 5..

Rated power input

–for heating up

– for maintaining heat

200

Heating time

min 7

Gluing temperature

°C 200

Gluing capacity

g/min 20

Glue stick diameter

mm 11

Glue stick length

mm 45–200

Weight according to

EPTA-Procedure 01/2003 kg 0.35

Protection class

/II

The values given are valid for a nominal voltage [U] of 230 V. For differ-

ent voltages and models for specific countries, these values can vary.

OBJ_BUCH-868-002.book Page 7 Monday, March 26, 2012 8:57 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch PKP 18 E Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info