110140
26
Zoom out
Zoom in
Vorherige Seite
1/151
Nächste Seite
26 | English
1 609 929 N78 | (7.2.08) Bosch Power Tools
The guide-rail adapter 26 is required for working
with the guide rail 27. The guide-rail adapter 26
is mounted in the same manner as the parallel
guide 10.
The following work steps are required for exact
cuts using the guide rail 27:
Place the guide rail 27 on to the workpiece
projecting lightly over the side. Pay attention
that the side with the rubber lip faces to the
workpiece.
Set the circular saw with the premounted
guide-rail adapter 26 on to the guide rail 27.
Adjust the desired cutting depth and the bev-
el angle. Observe the marks on the guide-rail
adapter 26 for preadjustment of the various
bevel angles; see figure F.
Align the circular saw with guide-rail adapter
in such a manner that the teeth of the saw
blade 21 face against the rubber lip. The po-
sition of the saw blade 21 depends on the se-
lected cutting angle. Do not saw into the
guide rail.
Tighten wing bolt 7 to lock the position of the
guide-rail adapter.
Remove the circular saw with the premount-
ed guide-rail adapter 26 from the guide rail
27.
Align the guide rail 27 on the workpiece in
such a manner that the rubber lip lies exactly
alongside the cutting edge.
Fasten the guide rail 27 with suitable clamp-
ing devices, e. g., screw clamps, on the work-
piece. Set the circular saw with the pre-
mounted guide-rail adapter 26 on to the
guide rail.
Switch the machine on and guide it in the
cutting direction applying moderate and
steady feed.
Two guide rails can be connected to one with
use of the connection piece 28. Clamping is car-
ried out with the four screws located in the con-
nection piece.
Maintenance and Service
Maintenance and Cleaning
f Before any work on the machine itself, pull
the mains plug.
f For safe and proper working, always keep
the machine and ventilation slots clean.
The retracting blade guard must always be able
to move freely and retract automatically. There-
fore, always keep the area around the retracting
blade guard clean. Remove dust and chips by
blowing out with compressed air or with a
brush.
Saw blades that are not coated can be protect-
ed against corrosion with a thin coat of acid-free
oil. Before use, the oil must be removed again,
otherwise the wood will become soiled.
Resin and glue residue on the saw blade produc-
es poor cuts. Therefore, clean the saw blade im-
mediately after use.
If the machine should fail despite the care taken
in manufacturing and testing procedures, repair
should be carried out by an after-sales service
centre for Bosch power tools.
In all correspondence and spare parts order,
please always include the 10-digit article
number given on the type plate of the machine.
0° 1
-
45°
OBJ_BUCH-179-003.book Page 26 Thursday, February 7, 2008 9:51 AM
26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Bosch PKS 40 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Bosch PKS 40

Bosch PKS 40 Bedienungsanleitung - Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch - 88 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info