Bedienungsanleitung Bosch PKS 54 CE (Seite 27 von 168) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

110143

Zoom out

Zoom in

Vorherige Seite

1/168

Nächste Seite

English | 27

Bosch Power Tools 1 609 929 N30 | (4.2.08)

Operation

Operating Modes

f Before any work on the machine itself, pull

the mains plug.

Adjusting the Cutting Depth (see figure B)

f Adjust the cutting depth to the thickness of

the workpiece. Less than a full tooth of the

blade teeth should be visible below the work-

piece.

Loosen the clamping lever 24. For a smaller cut-

ting depth, pull the saw away from the base

plate 15; for a larger cutting depth, push the

saw toward the base plate 15. Adjust the de-

sired cutting depth at the cutting -depth scale.

Tighten the clamping lever 24 again.

The tightening tension of the clamping lever 24

can be readjusted. For this, unscrew the clamp-

ing lever 24, and screw it back again turned off-

set by at least 30° in anticlockwise direction.

Adjusting the Cutting Angle

It is best to place the machine on the face side

of the blade guard 17.

Loosen the wing bolts 8 and 16. Tilt the saw

sidewards. Adjust the desired measure on the

scale 7. Tighten the wing bolts 8 and 16 again.

Note: For bevel cuts, the cutting depth is small-

er than the setting indicated on the cutting-

depth scale 25.

Cutting Marks

The 0° cutting mark (11) indicates the position

of the saw blade for right-angled cuts. The 45°

cutting mark (10) indicates the position of the

saw blade for 45° cuts.

For precise cuts, position the circular saw

against the workpiece as shown in the figure. It

is best to carry out a trial cut.

Starting Operation

f Observe correct mains voltage! The voltage

of the power source must agree with the

voltage specified on the nameplate of the

machine. Power tools marked with 230 V

can also be operated with 220 V.

Switching On and Off

To start the machine, first push the lock-off but-

ton for the On/Off switch 1 and then press the

On/Off switch 3 and keep it pressed.

To switch off the machine, release the On/Off

switch 3.

Note: For safety reasons, the On/Off switch 3

cannot be locked; it must remain pressed during

the entire operation.

Reduced starting current (PKS 54 CE/

PKS 66 CE)

The electronic reduced starting current limits

the power consumption when switching the tool

on and enables operation from a 13 ampere

fuse.

Constant Electronic Control (PKS 54 CE/

PKS 66 CE)

Constant electronic control holds the speed

constant at no-load and under load, and ensures

uniform working performance.

Temperature Dependent Overload Protection

(PKS 54 CE/PKS 66 CE)

In case of overload, the machine switches off

until the optimal operating-temperature range is

reached again. Release the On/Off switch 3 and

switch the machine on again to continue work-

ing.

Speed preselection (PKS 54 CE/PKS 66 CE)

The required speed can be preselected with the

thumbwheel 2 (also while running).

The required speed depends on the saw blade

being used and on the material being worked

(see overview of saw blades at the end of these

operating instructions).

0 45

OBJ_BUCH-662-001.book Page 27 Monday, February 4, 2008 11:14 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch PKS 54 CE Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info