Bedienungsanleitung Bosch PKS 66 (Seite 29 von 168) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

110155

Zoom out

Zoom in

Vorherige Seite

1/168

Nächste Seite

English | 29

Bosch Power Tools 1 609 929 N30 | (4.2.08)

The following work steps are required for exact

cuts using the guide rail 29:

– Place the guide rail 29 on to the workpiece

projecting lightly over the side. Pay attention

that the side with the rubber lip faces to the

workpiece.

– Set the circular saw with the premounted

guide-rail adapter 28 on to the guide rail 29.

– Adjust the desired cutting depth and the bev-

el angle. Observe the marks on the guide-rail

adapter 28 for preadjustment of the various

bevel angles; see figure G.

– Align the circular saw with guide-rail adapter

in such a manner that the teeth of the saw

blade 21 face against the rubber lip. The po-

sition of the saw blade 21 depends on the se-

lected cutting angle. Do not saw into the

guide rail.

– Tighten wing bolt 9 to lock the position of the

guide-rail adapter.

– Remove the circular saw with the premount-

ed guide-rail adapter 28 from the guide rail

29.

– Align the guide rail 29 on the workpiece in

such a manner that the rubber lip lies exactly

alongside the cutting edge.

– Fasten the guide rail 29 with suitable clamp-

ing devices, e. g., screw clamps, on the work-

piece. Set the circular saw with the pre-

mounted guide-rail adapter 28 on to the

guide rail.

– Switch the machine on and guide it in the

cutting direction applying moderate and

steady feed.

Two guide rails can be connected to one with

use of the connection piece 30. Clamping is car-

ried out with the four screws located in the con-

nection piece.

Maintenance and Service

Maintenance and Cleaning

f Before any work on the machine itself, pull

the mains plug.

f For safe and proper working, always keep

the machine and ventilation slots clean.

The retracting blade guard must always be able

to move freely and retract automatically. There-

fore, always keep the area around the retracting

blade guard clean. Remove dust and chips by

blowing out with compressed air or with a

brush.

Saw blades that are not coated can be protect-

ed against corrosion with a thin coat of acid-free

oil. Before use, the oil must be removed again,

otherwise the wood will become soiled.

Resin and glue residue on the saw blade produc-

es poor cuts. Therefore, clean the saw blade im-

mediately after use.

If the machine should fail despite the care taken

in manufacturing and testing procedures, repair

should be carried out by an after-sales service

centre for Bosch power tools.

In all correspondence and spare parts order,

please always include the 10-digit article

number given on the type plate of the machine.

0° 1

45°

OBJ_BUCH-662-001.book Page 29 Monday, February 4, 2008 11:14 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch PKS 66 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info