Bedienungsanleitung Bosch PLS 300 Set (Seite 16 von 130) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

544019

Zoom out

Zoom in

Vorherige Seite

1/130

Nächste Seite

16 | English

1 609 929 W68 | (21.6.11) Bosch Power Tools

Practical Advice

The following tips are for performing length or mitre cuts (90°/45°).

For working instructions and practical advice on the PLS 300

saw station, log onto: www.bosch-do-it.com/pls300

For further questions, please refer to our customer hotline:

Great Britain

Tel: +44 (0844) 736 0107

Australia, New Zealand

Phone: +61 (01300) 307 044

Operation

Cutting tiles

Preparing for Operation

When the sawing station is to be used for cutting tiles, the ad-

ditional PTC 1 kit is to be used.

The stop 15 is supplied as two parts, folded together.

– Before using for the first time, put the two parts of the stop

15 together, so that they cannot be taken apart after-

wards.

Lengthway Cuts (see figures F1–F3)

– Loosen the locking knob 3 a few turns.

– Turn the locking lever 10 of the guide rail leftward and fold

the guide rail 4 upward.

–Place stop 15 centred in the groove of bridge 8 and slide it

flush into base unit 1.

– Mark the desired cutting line on the workpiece.

– Place down the workpiece with the visible side up, flat

against the stop 15.

– Fold the guide rail 4 down and align the workpiece cutting

line to the scale of the stop 15.

– Press down the guide rail 4 in the area of the workpiece

with your flat hand.

– Tighten the locking knob 3.

– Lock the guide rail 4 with locking lever 10.

Diagonal Cuts (see figure G)

The mitre angle can be set in the range from 45° (left side) to

45° (right side).

– Loosen locking knob 12.

– Turn the guide rail 4 left or right until the angle indicator 13

indicates the requested mitre angle.

– Tighten the locking knob 12 again.

For swift and precise adjustment of standard mitre angles,

the guide rail engages at 0° and 45°.

– For additional worksteps, see “Lengthway Cuts” on

page 16.

Problem Cause Corrective Measure

Cut runs out of centre

Guide rail 4 not affixed Affix guide rail according to height of workpiece;

provide for firm clamping of the workpiece

Saw blade too thin Use the provided saw blade T144DP

Sawing feed too high

(apply less feed with power tool)

Saw through workpiece applying less and uni-

form feed

Do not apply pressure against the side stops 5

Angle adjustment of base plate to saw chain in-

correct

Align base plate to saw chain and retighten

Saw blade does not run in guide roller

(see figure E)

Adjust guide roller in such a manner that the saw

blade is guided (see operating instructions of

the jigsaw)

Wood surface unsatisfactory

after cut

Workpiece was sawn with the visible side facing

Saw workpiece with the visible side facing down

(see figure A3)

Saw blade worn Insert new saw blade

Sawing feed too high

(apply less feed with power tool)

Saw through workpiece applying less and uni-

form feed

Do not apply pressure against the side stops 5

Sawing was carried out with orbital action

switched on

Switch orbital action off

OBJ_BUCH-1219-002.book Page 16 Tuesday, June 21, 2011 2:15 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch PLS 300 Set Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info