Bedienungsanleitung Bosch POF1100AE (Seite 16 von 99) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

23201

Zoom out

Zoom in

Vorherige Seite

1/99

Nächste Seite

English - 4

Speed Table

The values shown in the chart are standard val-

ues. The necessary speed depends on the mate-

rial and the operating conditions, and can be de-

termined by practical testing.

Constant Electronic Control

(POF 1300 ACE)

Constant electronic control holds the speed con-

stant at no-load and under load, and ensures uni-

form working performance.

Depending on the cutting operation, the depth-of-

cut can be preset in several steps.

The adjustment of the depth-of-cut may

only be carried out when the router is

switched off.

Coarse Adjustment of the Depth-of-cut

– Place the router on the workpiece to be ma-

chined.

POF 1300 ACE: Set the fine adjustment for

depth-of-cut in the center position with fine-ad-

justment knob 1; to do this, turn the fine-adjust-

ment knob until the markings 24 on the backside

of the router are in alignment, as shown.

Afterwards turn scale 2 to “0” (see figure ).

Set step buffer 11 to the lowest position; the

buffer snaps-in noticeably.

POF 1100 AE: Set the screws for the step

buffer 21 halfway in or out.

Set step buffer 11 to the lowest position; the

buffer snaps-in noticeably. When fine adjustment

of the depth-of-cut is desired, select one of the

3 steps that is fitted with the screw 21.

POF 1100 AE/POF 1300 ACE:

– Loosen locking screw 8, so that depth stop 6

can be moved freely.

– Release the clamping lever 3 by turning in

clockwise direction and slowly lower the router

until the router bit touches the surface of the

workpiece. Lock the router in position by turn-

ing the clamping lever 3 in anticlockwise direc-

tion.

– Press depth stop 6 downwards until it touches

the stop buffer 11. Press down slider 7 and set

to “0”.

– Adjust the depth stop 6 to the required routing

depth and tighten the wing screw 8. It is impor-

tant that the slider 7 is not adjusted afterwards.

– Release the clamping lever 3 and guide the

router back up again.

The coarse adjustment of the depth-of-cut should

be checked by a trial cut and corrected, if neces-

sary.

Fine Adjustment of the Depth-of-cut

(POF 1300 ACE)

After a trial cut, fine adjustment can be carried out

by turning the fine adjustment knob 1 (1 scale

mark = 0.1 mm/1 rotation = 2.0 mm). The max-

imum adjustment is approx. +/– 8 mm.

Example: Slide router upwards again and meas-

ure the depth-of-cut (set value = 10.0 mm; actual

value = 9.8 mm).

– Lift up router and underlay guide plate 13 in

such a manner that the router can plunge

freely without the router bit touching the work-

piece.

Lower the router again until the depth stop 6

touches the step buffer 11.

– Afterwards set scale 2 to “0”.

– Loosen wing screw 8.

– With the fine adjustment 1, advance the depth-

of-cut in clockwise direction by 0.2 mm/

2 scale marks (= difference between required

value and actual value).

– Retighten wing screw 8 again.

– Slide router upwards again and check depth-

of-cut by carrying out another trial cut.

After setting the depth-of-cut, the position of the

index mark 7 on the depth stop should not be

changed anymore so that the currently adjusted

setting can always be read off of scale 5.

Material Router bit-Ø Speed stages

Hardwood 4 –10 mm 5–6

(Beech) 12 –20 mm 3–4

22 –40 mm 1–2

Softwood 4– 10 mm 5–6

(Pine) 12 –20 mm 3–6

22 –40 mm 1–3

Particle board 4 –10 mm 3–6

12 –20 mm 2–4

22 –40 mm 1–3

Plastic 4 –15 mm 2–3

16 –40 mm 1–2

Aluminium 4 –15 mm 1–2

16 –40 mm 1

Setting the Depth-of-cut

1 609 929 F23 - Buch Seite 4 Montag, 19. April 2004 8:27 08

16 • 1 609 929 F23 • 04.04

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch POF1100AE Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bosch POF1100AE

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info