Bedienungsanleitung Bosch POF1300ACE (Seite 15 von 99) (Englisch, Französisch, Spanisch)

23203

Zoom out

Zoom in

Vorherige Seite

1/99

Nächste Seite

English - 3

Inserting Router Bits (see figure )

■ Before any work on the machine itself, pull the

mains plug.

■ It is recommended to wear protective gloves

when inserting or replacing router bits.

Fold down chip shield 15.

Press spindle lock button 18 and keep de-

pressed. If required, turn the spindle by hand until

the lock engages.

■ Press the spindle lock button only when at a

standstill.

Insert router bit. The shank of the router bit must

be inserted at least 20 mm (shank length).

Tighten the tightening nut 17 with the open-end

spanner 25 (size 19 mm). Release the spindle

lock button 18.

Fold up chip shield 15.

Do not tighten the tightening nut of the

collet without a router bit inserted.

■ The dust that is produced while working can be

detrimental to health, inflammable or explo-

sive. Suitable safety measures are required.

Examples: Some dusts are regarded as carci-

nogenic. Use suitable dust/chip extraction and

wear a dust respirator.

■ Dust from light alloys can burn or explode. Al-

ways keep the workplace clean, as blends of

materials are particularly dangerous.

Mounting the Extraction Adapter

(see figure )

Press the chip shield 15 together at the holding

fixture on the base plate and remove it.

Fasten dust-collection adapter 27 to base

plate 12 with both knurled screws 26 and connect

vac via suction hose 28 (accessory).

☞

When mounting the extraction adapter,

ensure correct mounting position!

For dust extraction, the 35-mm-Ø vacuum

hose 28 can be connected directly to the extrac-

tion adapter.

Clean the extraction adapter 27 regularly to en-

sure optimum dust extraction at all times.

The machine can be plugged directly into the re-

ceptacle of a Bosch all-purpose vacuum cleaner

with remote starting control. The vacuum cleaner

starts automatically when the machine is

switched on.

The vacuum cleaner must be suitable for the ma-

terial to be worked.

When vacuuming dry dust that is especially detri-

mental to health or carcinogenic, use a special

vacuum cleaner.

Observe correct mains voltage: The voltage of

the power source must agree with the voltage

specified on the nameplate of the machine.

Equipment marked with 230 V can also be con-

nected to 220 V.

Switching On and Off

For starting operation of the machine, actuate

the lock-off button 20 first, and then press and

hold the On/Off switch 23 afterwards.

POF 1300 ACE: A lamp lights out the routing.

To switch off the machine, release the On/Off

switch 23.

POF 1300 ACE: The lamp slowly goes out.

Speed Preselection

The required speed can be preselected with the

thumbwheel 22 (also while running).

1 –2 = low speed

3 –4 = medium speed

5 –6 = high speed

The required speed is dependent on the material

and can be determined by practical testing.

After longer periods of working at low speed, al-

low the machine to cool down by running it for ap-

prox. 3 minutes at maximum speed with no load.

Dust/Chip Extraction

Initial Operation

1 609 929 F23 - Buch Seite 3 Montag, 19. April 2004 8:27 08

15 • 1 609 929 F23 • 04.04

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch POF1300ACE Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bosch POF1300ACE

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info