Bedienungsanleitung Bosch POF1300ACE (Seite 17 von 99) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

23203

Zoom out

Zoom in

Vorherige Seite

1/99

Nächste Seite

English - 5

Fine Adjustment of the Depth-of-cut

(POF 1100 AE)

With the step buffer 11, up to three different rout-

ing depths can be preset. Adjustment is carried

out according to the previously described proce-

dure, with the difference that by screwing in or out

the screws for the step buffer 21, the height clear-

ance of the stops, in reference to each other, can

be changed.

Usage of the Step Buffer

a) Dividing the cutting procedure in several

steps

For deep cuts, it is recommended to carry out

several cuts, each with less material removal. By

using the step buffer 11, the cutting process can

be divided into several steps.

Set the required depth-of-cut with the lowest step

of the step buffer. Afterwards, the higher steps

can be used for the first two cuts.

b) Pre-adjustment of varying depth-of-cuts

If several different depth-of-cuts are required for

the machining of a workpiece, these can also be

pre-adjusted by using the step buffer 11.

Direction of Feed

The feed motion of

the router must al-

ways be carried out

against the rotation

direction of the

router bit (up-grind-

ing).

When milling in the

direction with the ro-

tation of the router

bit (down-cutting),

the router can break

loose, eliminating

control by the user.

Routing Process

Adjust the depth-of-cut as previously described.

Place the router on the workpiece and switch on.

Release the clamping lever 3 by turning in clock-

wise direction and slowly lower the router until the

depth stop 6 runs against the workpiece. Lock

the router in position by turning the clamping le-

ver 3 in anticlockwise direction. Cary out the cut-

ting procedure with uniform feed.

After finishing the cutting process, slide the router

upwards again and switch off.

Routing with Guide Bushing

The guide bushing 29 enables template and pat-

tern routing on workpieces.

Inserting guide bushing 29 (see figure )

Insert guide bushing 29 in the bottom of the guide

plate 13 by actuating the locking lever 10. Ensure

that the encoding keys clearly engage in the

grooves of the guide bushing.

Routing Process (see figure )

Choose a router bit with a smaller diam-

eter than the inner diameter of the guide

bushing.

Set the router with guide bushing 29 against the

template. Release the clamping lever 3 by turn-

ing in clockwise direction and slowly lower the

router toward the workpiece until the adjusted

depth-of-cut is reached.

Guide router with projecting guide bushing along

the template, applying light sideward pressure.

Note: The template must have a minimum thick-

ness of 8 mm, due to the projecting height of the

guide bushing.

Routing with Guide Rail (see figure )

Fasten a suitable guide rail with an appropriate

clamping device (screw clamp) to the workpiece.

Guide the flattened side of the guide plate along

the guide rail.

Note the direction of feed:

To avoid the router from “running off” of the

guide rail, it is important that the router is

led as shown.

Shaping or Molding Applications

For shaping or molding applications without the

use of a parallel guide, the router must be

equipped with a pilot or a ball bearing.

Lead the router sidewards to the workpiece and

allow router bit to engage until the pilot or the ball

bearing of the router reach the corner of the work-

piece being machined. Guide the router along-

side the workpiece corner using both hands, en-

suring proper seating of the base plate. Too

much pressure can damage the edge of the

workpiece.

Operating Instructions

1 609 929 F23 - Buch Seite 5 Montag, 19. April 2004 8:27 08

17 • 1 609 929 F23 • 04.04

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch POF1300ACE Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bosch POF1300ACE

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info