Bedienungsanleitung Bosch PowerTube 750 BBP3770 - 2022 (Seite 14 von 63) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

780120

Zoom out

Zoom in

Vorherige Seite

1/63

Nächste Seite

English – 2

0 275 007 3PX | (09.07.2021) Bosch eBike Systems

(4) PowerTube battery (pivot)

(5) Socket for charging connector

(6) Operation/battery charge indicator

(7) On/off button

(8) PowerTube battery safety restraint

(9) Locking mechanism

(10) Pull strap

(11) Axial rail

(12) PowerTube battery (axial)

(13) Upper axial PowerTube holder

Technical data

Li-ion battery PowerTube750

Product code Horizontal BBP3770

Product code Vertical BBP3771

Rated voltage V= 36

Nominal capacity Ah 20.1

Energy Wh 750

Operating temperature °C –5to+40

Storage temperature °C +10to+40

Permitted charging temperature

range °C 0to+40

Weight, approx. kg 4.4

Protection rating IP54

Fitting

uEnsure the battery is placed on clean surfaces only.

Avoid getting dirt, e.g. sand or soil, in the charging socket

and contacts in particular.

Testing the battery before using it for the first

time

Test the battery before charging it for the first time or using

it in your eBike.

To do this, press the on/off button (7) to switch the battery

on. If none of the LEDs on the battery charge indicator (6)

light up, the battery may be damaged.

If at least one (but not all) of the LEDs on the battery charge

indicator (6) lights up, the battery will need to be fully

charged before using it for the first time.

uDo not charge or use batteries if they are damaged.

Contact an authorised bicycle dealer.

Charging the battery

uA Bosch eBike battery must only be charged using an

original Bosch eBike charger.

Note: The battery is supplied partially charged. To ensure

full battery capacity, fully charge the battery in the charger

before using it for the first time.

To charge the battery, read and follow the instructions in the

operating manual for the charger.

The battery can be charged at any state of charge. Interrupt-

ing the charging process does not damage the battery.

The battery has a temperature monitoring function which

only allows it to be charged within a temperature range of

0°C to 40°C.

If the temperature of the bat-

tery is outside this charging

range, three of the LEDs on

the battery charge indicator

(6) will flash. Disconnect the

battery from the charger and

let it acclimatise.

Do not reconnect the battery to the charger until it has

reached the correct charging temperature.

Battery charge indicator

The five green LEDs on the battery charge indicator (6) in-

dicate the battery's state of charge of when the battery is

switched on.

Each LED represents approximately 20% of the charging ca-

pacity. When the battery is fully charged, all five LEDs will be

lit.

The battery's state of charge when switched on is also shown

on the display of the on-board computer. Read and follow

the instructions in the operating manuals for the drive unit

and on-board computer.

If the battery capacity is less than 5%, all the LEDs on the

battery charge indicator (6) on the battery will go out. The

display function of the on-board computer, however, will

carry on working.

Once charging is complete, disconnect the battery from the

charger and the charger from the mains.

Inserting and removing the battery

uAlways switch off the battery and the eBike system

when inserting the battery into the holder or remov-

ing it from the holder.

Removing the PowerTube battery (pivot) (seefigureA)

❶To remove the PowerTube battery(4), open the

lock(2) using the key(1). The battery will be unlocked

and fall into the safety restraint(8).

❷Press on the safety restraint from above. The battery

will be unlocked completely and fall into your hand.

Pull the battery out of the frame.

Note: As a result of varying designs, the battery may need

to be inserted and removed using a different method. Read

the operating instructions of the eBike manufacturer.

Inserting the PowerTube battery (pivot) (seefigureB)

In order for the battery to be inserted, the key (1) must be

inserted into the lock (2) and the lock must be open.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch PowerTube 750 BBP3770 - 2022 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info