Bedienungsanleitung Bosch PPR 250 (Seite 19 von 184) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

544063

Zoom out

Zoom in

Vorherige Seite

1/184

Nächste Seite

English | 19

Bosch Power Tools 2 609 006 717 | (26.11.13)

Correction of Malfunctions

Maintenance and Service

 Before any work on the machine itself, pull the mains

plug.

Cleaning

After painting, the system must be pumped empty and all

paint-carrying parts must be cleaned.

There are two possibilities for cleaning the system:

– EasyClean: Using universal connectors, the system is con-

nected to a water tap and flushed.

– Alternative possibility: The system pumps fresh water

from a bucket for cleaning.

Proper cleaning is a prerequisite for perfect operation of the

electric paint roller. No warranty claims can be undertaken if

cleaning is not carried out or is carried out incorrectly.

Keep the base unit, the holding clip 28 and the remote control

8 clean. Clean them with a moist cloth. The base unit and the

remote control may not be immersed into water.

Always clean the paint roll, the paint applicator and the hose

system with water.

Preparation

– Place down the paint applicator 3 on the edge of the paint

bucket so that it rests on the bucket holder 14.

– Loosen the double-SDS-connector 27 from the holding

clip 28 and completely remove the intake hose 4 and the

paint filter 22 from the paint bucket.

– Remove the paint roll 16 from the paint applicator 3 (see

“Changing the Paint Roll”, page 18).

– Hold the paint applicator 3 above the paint bucket and press

the trigger switch 7 until the hose system is pumped empty

and no more paint comes out of the paint applicator.

– Release the trigger switch 7 and switch the power tool off.

– Pull the mains plug from the socket outlet.

EasyClean (see figures G1 –G4)

Note: Use only the supplied hoses and adapters for connect-

ing to the water supply.

Preparing the water tap:

– Unscrew the mixing nozzle from a water tap using the sup-

plied mixing-nozzle spanner 30 or a suitable tool.

– Screw the fitting adapter 31 (M22 or M24 thread) in or on

the water tap.

Additional water-tap adapters are available in the Bosch

accessories program.

Separating paint-carrying components:

– Unlatch holding clamp 21.

– Disengage pump lock 23.

To relieve the lock tension, lightly push the pump lid 20 up-

ward, if required.

– Push the pump lid 20 downward to the stop and then care-

fully lift it out of the housing opening of base unit 5.

– Loosen the SDS connection 32 at the bottom part of the in-

take hose 4.

Flushing the system:

– Carry the paint applicator 3, feed hose 2, pump lid 20 and

intake hose 4 to the prepared water tap.

Please note that paint may escape or leak from the system.

Problem Cause Corrective Measure

Paint application unsatisfactory.

The hoses are obstructed. No or too little

paint being transported.

Make sure that none of the hoses are

squeezed or creased.

The paint is too viscous and therefore

cannot be transported.

Stir the paint thoroughly and dilute it with

5 –10% water if necessary.

The pump lock 23 is not engaged. Make sure that pump lid 20 is properly in-

serted and locked.

The paint bucket is empty. Refill the paint bucket with fresh paint or ex-

change the empty paint bucket against a full

one.

No paint coming out of paint applicator 3.

The paint is too viscous and cannot be

drawn in by the pump.

Stir the paint thoroughly and dilute it with

5 –10% water if necessary.

The hoses are obstructed. Clean the hose system (see “Cleaning”,

page 19).

The hoses are obstructed. No or too little

paint being transported.

Make sure that none of the hoses are

squeezed or creased.

The remote control 8 is inoperative. The base unit is switched off. Switch the base unit on (see “"Switching

On"Switching On”, page 18).

The remote control battery is empty. Contact an authorised service agent for

Bosch power tools.

Have the component replaced there.

Note: The battery never has to be replaced

in normal use.

OBJ_BUCH-1513-004.book Page 19 Tuesday, November 26, 2013 4:07 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch PPR 250 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info