Bedienungsanleitung Bosch psb 500 (Seite 20 von 120) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

387167

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

20 | English

2 609 005 111 | (2.12.10) Bosch Power Tools

Mounting the Extraction Device (see figure A)

Guide the extraction device 12 from the front to-

ward the bottom side of the impact drill. Pay at-

tention that the extraction device 12 faces flush

against the casing and that it is locked.

Cleaning the Extraction Device

(see figures B–D)

The dust collector 13 is sufficient for approx.

10 drillings with a drilling diameter of 10 mm.

When the extraction force diminishes or when

the level indicator 14 is full, the dust collector

13 must be emptied. For this, press on the rif-

fled surface of the release button 16 and take

off the dust collector 13.

Empty and clean the dust collector 13. Clean the

filter element 17 by gently striking or tapping

against it.

Check the filter element 17 for damage and re-

place it as required.

Press on the holder of the filter element 17 and

pull it out. Replace the filter element 17 includ-

ing the holder. When placing on the holder

again, make sure that the rubber gasket 18 is in-

serted.

Reattach the dust collector 13 again and lock it

by pressing against the smooth surface of the

release button 16.

Removing the Extraction Device (see figure E)

For disassembly of the extraction device 12,

press release button 20 and pull off the extrac-

tion device 12 toward the front.

Stowing the Extraction Device (see figure F)

For stowing the extraction device 12 in the case,

remove the extraction device 12, slide it togeth-

er and attach clamp 21.

Attach the locking latch 22 or empty the dust

collector 13 before placing down the extraction

device.

Auxiliary Handle

f Operate your machine only with the auxilia-

ry handle 10.

The auxiliary handle 10 can be set to any posi-

tion for a secure and low-fatigue working pos-

ture.

Turn the wing bolt for adjustment of the auxilia-

ry handle 11 in anticlockwise direction and set

the auxiliary handle 10 to the required position.

Then tighten the wing bolt 11 again in clockwise

direction.

Adjusting the Drilling Depth (see figure G)

The required drilling depth X can be set with the

depth stop 1.

Press the button for the depth stop adjustment

5 and insert the depth stop into the auxiliary

handle 10.

The knurled surface of the depth stop 1 must

face downward.

Pull out the depth stop until the distance be-

tween the tip of the drill bit and the tip of the

depth stop correspond with the desired drilling

depth X.

Changing the Tool (see figure H)

Keyless Chuck

Hold the rear sleeve 3 of the keyless chuck 4

tight and turn the front sleeve 2 in rotation di-

rection n, until the tool can be inserted. Insert

the tool.

Hold the rear sleeve 3 of the keyless chuck 4

tight and firmly turn the front sleeve 2 in rota-

tion direction o by hand.

Screwdriver Tools

When working with screwdriver bits 24, a uni-

versal bit holder 23 should always be used. Use

only screwdriver bits that fit the screw head.

For driving screws, always position the “Drill-

ing/Impact Drilling” selector switch 6 to the

“Drilling” symbol.

OBJ_BUCH-862-005.book Page 20 Thursday, December 2, 2010 5:16 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch psb 500 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info