Bedienungsanleitung Bosch psb 700 res (Seite 21 von 117) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

388578

Zoom out

Zoom in

Vorherige Seite

1/117

Nächste Seite

English | 21

Bosch Power Tools 1 609 929 N03 | (10.10.07)

If the preselected torque is reached during

screwdriving, the machine switches off; the drill-

ing tool no longer rotates. If the load on the ma-

chine is then removed with the On/Off switch 6

still pressed, the drilling tool continues to run on-

ly at very low speed for safety reasons.

After briefly releasing the On/Off switch 6, the

next screw can be driven in with the same

torque.

For screwdriving without torque lim-

itation, turn the thumbwheel 3 to the

right stop. This setting is required,

when the torque in position III is not

sufficient.

Working Advice

f Apply the power tool to the screw/nut only

when it is switched off. Rotating tool inserts

can slip off.

Tips

After longer periods of working at low speed, al-

low the machine to cool down by running it for

approx. 3 minutes at maximum speed with no

load.

For drilling in tiles, set the selector switch 2 to

the “Drilling” symbol. Do not switch over to the

symbol “Impact Drilling” or work with impact un-

til after drilling through the tile.

Use carbide tipped drill bits when working in

concrete, masonry and brick wall.

For drilling in metal, use only perfectly sharp-

ened HSS drill bits (HSS=high-speed steel). The

appropriate quality is guaranteed by the Bosch

accessories program.

Twist drills from 2.5–10 mm can easily be sharp-

ened with the drill bit sharpener (see accesso-

ries).

Maintenance and Service

Maintenance and Cleaning

f Before any work on the machine itself, pull

the mains plug.

f For safe and proper working, always keep

the machine and ventilation slots clean.

If the machine should fail despite the care taken

in manufacturing and testing procedures, repair

should be carried out by an after-sales service

centre for Bosch power tools.

In all correspondence and spare parts order,

please always include the 10-digit article number

given on the type plate of the machine.

WARNING! Important instructions for connect-

ing a new 3-pin plug to the 2-wire cable.

The wires in the cable are coloured according to

the following code:

Do not connect the blue or brown wire to the

earth terminal of the plug.

Important: If for any reason the moulded plug is

removed from the cable of this power tool, it

must be disposed of safely.

After-sales service and customer assist-

ance

Our after-sales service responds to your ques-

tions concerning maintenance and repair of your

product as well as spare parts. Exploded views

and information on spare parts can also be found

under:

www.bosch-pt.com

Our customer consultants answer your questions

concerning best buy, application and adjustment

of products and accessories.

OBJ_BUCH-530-001.book Page 21 Wednesday, October 10, 2007 10:49 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch psb 700 res Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info