Bedienungsanleitung Bosch PSB24VE_2 (Seite 11 von 67) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

16604

Zoom out

Zoom in

Vorherige Seite

1/67

Nächste Seite

English - 3

Open the drill chuck 3 by turning until the tool can

be inserted. Insert the tool.

Firmly tighten the sleeve of the keyless chuck 3

by hand until the locking action (“click”) is no

longer heard. This automatically locks the chuck.

Rotate the sleeve in the reverse direction to re-

move the tool.

Screwdriving (see figure )

Directly clamp the screwdriver bit 7 into the drill

chuck or use the additional universal bit holder 12

when operating with hex shank bits 11.

Inserting the Battery

Set the rotational direction switch 8 to the centre

position = lock-off and allow the charged bat-

tery 5 to engage into the handle.

Switching On and Off

To start the machine, press the On/Off switch 9

and keep it depressed.

The machine runs with variable

speed between 0 and maximum,

depending on the pressure applied

to the On/Off switch 9. Light pres-

sure results in a low rotational

speed thus allowing smooth, con-

trolled starts. Do not strain the ma-

chine so heavily that it comes to a

standstill.

To switch off the machine, release the On/Off

switch 9.

Electric Brake

When releasing the On/Off switch 9 the speed of

the drill chuck is reduced to a stop, thus prevent-

ing the run-on of the tool.

For screwdriving applications, wait until the screw

is flush with the material and then release the On/

Off switch 9. The screw head does not penetrate

into the material then.

Gear Selection, Mechanical

Two speed ranges can be preselected with the

gear selector 1:

1st gear: Low rotational speed, high power.

2nd gear: High rotational speed, less power.

The speed settings may only be changed when

the machine is motionless. If the speed setting

has not quite notched in properly, briefly press

the On/Off switch 9.

Fully Automatic Spindle Locking

(Auto-Lock)

The drill spindle is locked when the On/Off

switch 9 is not pressed.

This makes quick and easy changing of the tool

in the drill chuck possible.

The locked drill chuck enables retightening of

projecting screws by using the switched-off ma-

chine as a screwdriver.

Reversing the Rotational Direction

Operate the rotational direction

switch 8 only at a standstill.

The rotational direction

switch 8 is used to re-

verse the rotational direc-

tion of the machine. How-

ever, this is not possible

with the On/Off switch 9

actuated.

Right Rotation ( )

Turn the rotational direction switch through to the

left stop (normal operation: drilling, screwdriving,

etc.).

Left Rotation ( )

Press the rotational direction switch through to

the right stop (for loosening and unscrewing

screws and nuts).

Changing the Tool

Starting Operation

11 • 2 609 932 336 • TMS • 26.01.04

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch PSB24VE_2 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bosch PSB24VE_2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info