Bedienungsanleitung Bosch PSM Primo (Seite 12 von 67) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch)

766877

Zoom out

Zoom in

Vorherige Seite

1/67

Nächste Seite

12 | English

Tap the hook-and-loop fastening of the sanding plate (3) be-

fore fitting the sanding sheet (4) to facilitate maximum adhe-

sion.

The sanding sheet (4) is equipped with two spare tips. If the

sanding sheet tip is worn, replace it with a spare sanding

sheet tip.

Position the sanding sheet (4) so that it is flush with one a

side of the sanding plate (3), then place the sanding sheet

on the sanding plate and press it on firmly.

To remove the sanding sheet (4), take hold of it by an edge

and pull it away from the sanding plate (3).

Choosing the sanding sheet

Different sanding sheets are available, depending on the ma-

terial you are working with and the required surface removal

rate:

Application Grit

For working all materials such as wood, paint,

filler, varnish, hard and softwood, and chip-

board

40–180

For pre-sanding, e.g. of rough and un-

even beams and boards Coarse 40

For surface sanding and levelling of

slight irregularities Medium 80, 120

For finishing and fine sanding of hard

woods Fine 180

Operation

Starting Operation

uPay attention to the mains voltage. The voltage of the

power source must match the voltage specified on the

rating plate of the power tool. Power tools marked

with 230V can also be operated with 220V.

uProducts that are only sold in AUS and NZ: Use a resid-

ual current device (RCD) with a nominal residual current

of 30 mA or less.

Switching on/off

uMake sure that you are able to press the On/Off switch

without releasing the handle.

To switch on the power tool, slide the on/off switch (1) for-

ward so that "1" appears on the switch.

To switch off the power tool, slide the on/off switch (1)

backward so that "0" appears on the switch.

Practical advice

uPull the plug out of the socket before carrying out any

work on the power tool.

uAlways wait until the power tool has come to a com-

plete stop before placing it down.

The material removal rate when sanding is primarily determ-

ined by the choice of sanding sheet.

Only immaculate sanding sheets achieve good sanding per-

formance and make the power tool last longer.

Be sure to apply consistent contact pressure in order to in-

crease the lifetime of the sanding sheets.

Excessively increasing the contact pressure will not lead to

increased sanding performance, rather it will cause more

severe wear of the power tool and of the sanding sheet.

To sand corners, edges and hard-to-reach areas accurately,

you can also work with the tips alone or with an edge of the

sanding plate.

Use only original Bosch-sanding accessories.

Maintenance and Service

Maintenance and Cleaning

uPull the plug out of the socket before carrying out any

work on the power tool.

uTo ensure safe and efficient operation, always keep

the power tool and the ventilation slots clean.

In order to avoid safety hazards, if the power supply cord

needs to be replaced, this must be done by Bosch or by an

after-sales service centre that is authorised to repair Bosch

power tools.

After-Sales Service and Application Service

Our after-sales service responds to your questions concern-

ing maintenance and repair of your product as well as spare

parts. You can find explosion drawings and information on

spare parts at: www.bosch-pt.com

The Bosch product use advice team will be happy to help you

with any questions about our products and their accessor-

ies.

In all correspondence and spare parts orders, please always

include the 10‑digit article number given on the nameplate

of the product.

Great Britain

Robert Bosch Ltd. (B.S.C.)

P.O. Box 98

Broadwater Park

North Orbital Road

Denham Uxbridge

UB 9 5HJ

At www.bosch-pt.co.uk you can order spare parts or arrange

the collection of a product in need of servicing or repair.

1 609 92A 68X | (14.04.2021) Bosch Power Tools

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch PSM Primo Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info