Bedienungsanleitung Bosch PSP260 (Seite 10 von 58) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch)

28082

Zoom out

Zoom in

Vorherige Seite

1/58

Nächste Seite

English–3

1 609 929 F37 • (03.08) T

Take care to maintain the same distance to the surface

to be sprayed and make uniform movement (see Fig.

First, spray the corners or small decorative parts with

short spray bursts. Then perform the actual spraying

procedure.

Begin the spraying pass approx. 10 cm outside the

surface to be sprayed and also end it approx. 10 cm

beyond the surface. Spray from the edge to the mid-

dle, then work the surface in a crosswise manner (see

Fig. ). A uniform application is achieved when the

passes overlap by 4 to 5 cm.

Then spray the surface a second time in the crosswise

manner.

When spraying on a vertical surface, drops can form.

First, spray from a somewhat greater distance and al-

low the sprayed material to partially dry.

Never spray until the container is empty. The suc-

tion tube must always be immersed in the fluid. Oth-

erwise, the spray mist is interrupted and thick drops

are sprayed.

Selecting Nozzles

(For illustrations of the accessories, see the last page

of these instructions.)

■ Before any work on the machine itself, pull the

mains plug.

■ Always keep the machine clean so that it functions

properly and accurately.

General Maintenance and Cleaning Instruc-

tions

The cleaning of the machine and the container 5 al-

ways takes place with the thinning agent suitable for

the spray material.

■ Never immerse the complete unit in cleaning agent!

For cleaning, spray through the machine with the thin-

ning agent or with water for water soluble material (use

the collecting basin).

After cleaning or use with water, briefly spray

resin- and acid-free oil (for example, sewing ma-

chine oil) through the machine for corrosion pro-

tection. Otherwise, the piston could become

blocked by rust.

Special Cleaning Instructions (see Fig. )

1. Screw out the attachment knob 2.

2. Separate the motor housing 11 from the pump unit

7. See Fig. for this purpose.

3. Unscrew the nozzle 1 and remove the suction/

pressure valve 6 from the pump unit 7. Remove

the pump piston 10 together with the spring 9 from

the pump unit 7. Do not use force!

4. Make a tightly fitting valve ball passable through

piston opening 8 with the aid of a copper or brass

pin.

5. Place all parts in the appropriate thinning agent and

clean.

Never use hard objects for cleaning! The

pump piston 10 must be free to move easily in the

pump housing.

6. Reassemble the parts in the reverse order.

For malfunctions, check the nozzle 1 and the suc-

tion/pressure valve 6 and replace as necessary.

After cleaning, briefly spray resin- and acid-free oil (for

example, sewing machine oil) through the machine for

corrosion protection.

Nozzle Application

cylindrical spray

nozzle:

– Ø 0.6 mm

(supplied)

all paints, varnishes

– Ø 0.4 mm liquid spray material

(water, solvents)

– Ø 0.8 mm viscous spray material

flat-spray nozzle:

– FD5 fine varnishing work

– FD7 dispersion paint

(airless quality)

cleaning nozzle thin, hard jet

nozzle extension spray, upwards or down-

wards (flexible 90°)

Maintenance and Cleaning

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch PSP260 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bosch PSP260

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info