Bedienungsanleitung Bosch PSR 12-2 (Seite 15 von 92) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

78260

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

English | 152 609 001 965 • 11.10.06

The vibration emission level given in

this information sheet has been meas-

ured in accordance with a standardised test given in

EN 60745 and may be used to compare one tool with

another.

The vibration emission level will vary because of the

ways in which a power tool can be used and may

increase above the level given in this information sheet.

This could lead to a significant underestimate of expo-

sure when the tool is used regularly in such a way.

Note: To be accurate, an estimation of the level of

exposure to vibration experienced during a given period

of work should also take into account the times when

the tool is switched off and when it is running but not

actually doing the job. This may significantly reduce the

exposure level over the total working period.

Assembly

Battery Charging

A battery that is new or has not been used for a longer

period does not develop its full capacity until after

approx. 5 charging/discharging cycles.

To remove the battery 9 press the unlocking buttons 8

and pull out the battery downwards. Do not exert any

force.

The battery is equipped with a NTC temperature con-

trol which allows charging only within a temperature

range of between 0 °C and 45 °C. A long battery serv-

ice life is achieved in this manner.

A significantly reduced working period after charging

indicates that the battery is used and must be replaced.

Observe the notes for disposal.

Changing the Tool (see figure A)

f Before any work on the machine (e. g., main-

tenance, tool change, etc.) as well as during

transport and storage, set the rotational

direction switch to the centre position. Unin-

tentional actuation of the On/Off switch can lead to

injuries.

The drill spindle is locked when the On/Off switch 12

is not pressed. This makes quick, convenient and easy

changing of the tool in the drill chuck possible.

Open the keyless chuck 1 by turning until the tool can

be inserted. Insert the tool.

Firmly tighten the collar of the keyless chuck 1 by hand

in clockwise direction until the locking action (“click”) is

no longer heard. This automatically locks the drill

chuck.

The locking is released again to remove the tool when

the collar is turned in the opposite direction.

Replacing the Drill Chuck

(see figures C–E)

f Before any work on the machine (e. g., main-

tenance, tool change, etc.) as well as during

transport and storage, set the rotational

direction switch to the centre position. Unin-

tentional actuation of the On/Off switch can lead to

injuries.

The keyless chuck 1 is secured with a securing screw

14 against unintentional loosening from the drill spin-

dle. Completely open the keyless chuck 1 and unscrew

the securing screw 14 in clockwise direction. Please

note that the securing screw has a left-hand

thread.

Removing the Drill Chuck (see figure D)

Clamp the short end of an Allen key 15 into the keyless

chuck 1.

Place the machine on a stable surface (e.g. a work-

bench). Hold the machine firmly and loosen the keyless

chuck 1 by turning the Allen key 15 in anticlockwise

direction. Loosen a tight-seated keyless chuck by giv-

ing the long end of the Allen key 15 a light blow.

Remove the Allen key from the keyless chuck and com-

pletely unscrew the keyless chuck.

Mounting the Drill Chuck (see figure E)

The keyless chuck is mounted in reverse order.

Note: After mounting the keyless chuck, screw the

securing screw 14 in again.

The drill chuck must be tightened with a

tightening torque of approx. 17–23 Nm.

Operation

Starting Operation

Inserting the Battery

f Use only original Bosch O-pack batteries with

the voltage given on the type plate of your

machine. The use of other batteries can lead to

injuries and danger of fire.

Set the rotational direction switch 11 to the centre

position in order to avoid unintentional starting. Insert

the charged battery 9 into the handle so that it can be

felt to engage and faces flush against the handle.

Reversing the Rotational Direction (see figure B)

The rotational direction switch 11 is used to reverse the

rotational direction of the machine. However, this is not

possible with the On/Off switch 12 actuated.

Right Rotation: For drilling and driving in screws,

push the rotational direction switch 11 left to the stop.

WARNING

OBJ_BUCH-213-001.book Page 15 Wednesday, October 11, 2006 8:37 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch PSR 12-2 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info