Bedienungsanleitung Bosch psr 1440 (Seite 4 von 13) (Englisch)

386423

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

English - 2

■

Secure the workpiece.

Clamping devices or a

vise will hold the workpiece in place better than

the hand.

■

Never allow children to use the machine.

■

Bosch can only guarantee a flawless function-

ing of the machine if the original accessories

intended for it are used.

Battery and Battery Charger

■

The enclosed operating instructions for the

battery charger must be read carefully!

■

Allow heated batteries to cool before charging.

■

Protect the battery from heat and fire: Explo-

sion risk! Do not place the battery on radiators

or expose it to strong sun rays for a long time

period; temperatures over 50 °C cause dam-

age.

■

Do not open the battery and protect from im-

pact. Store in a dry and frost-free place.

■

Do not dump the battery into the household

waste, fire or water.

Battery Charging

A battery that is new or has not been used for a

longer period does not develop its full capacity

until after approximately 5 charging/discharging

cycles.

To remove the battery

, press the unlocking but-

tons

and pull out the battery downwards. Do not

exert any force.

The battery is equipped with an NTC temperature

monitor which allows charging only within a tem-

perature range of 0 °C to 45 °C. This will prolong

the useful life of the battery.

A significantly reduced working period after

charging indicates a used up battery that must be

replaced.

■

Observe the indications regarding environ-

mental protection.

Open the chuck until the tool can be inserted.

Then, insert the tool.

Hold the rear sleeve tight and firmly tighten the

front sleeve by hand, until the locking ac-

tion (“click”) is no longer heard. The drill chuck is

locked automatically.

The locking is released again when the front col-

lar is turned in the opposite direction to remove

the tool.

Screwdriving (see figures + )

Clamp the bit

directly into the drill chuck. We

recommend using the universal bit holder

for

quick changes.

Inserting the Battery

Set the rotational direction switch

to the center

position = lock-off and allow the charged bat-

tery

to engage into the handle.

Switching On and Off

start

the unit, press the On/Off switch

The machine runs with variable

speed between 0 and maximum

depending on the pressure applied

to the On/Off switch

. Light pres-

sure results in a low rotational

speed, thus allowing smooth, con-

trolled starts. Do not load the ma-

chine so heavily that it comes to a

standstill.

switch off

the unit, release the On/Off

switch

Run-On Brake

When the On/Off switch

is released, the chuck

brakes to a stop, thus preventing the run-on of

the tool.

For screwdriving work, wait until the screw is

screwed in flush with the material and then re-

lease the On/Off switch

. By doing so, the head

of the screw does not penetrate into the material.

Before Use

Changing the Tool

Initial Operation

A B

2 609 140 210 - Buch Seite 2 Montag, 18. November 2002 8:07 08

4 • 2 609 140 210 • TMS • 13.11.02

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch psr 1440 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info