Bedienungsanleitung Bosch PSR12-2 (Seite 16 von 92) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

473377

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

16 | English 2 609 001 965 • 11.10.06

The indicator for right rotation 4 lights up when

the On/Off switch 12 is actuated and the motor

is running.

Left Rotation: For loosening or unscrewing screws,

push the rotational direction switch 11 right to the stop.

The indicator for left rotation 5 lights up when

the On/Off switch 12 is actuated and the motor

is running.

Setting the Torque

With the torque presetting ring 2 the required torque

setting can be preselected in 25 steps. With the cor-

rect setting, the insert tool is stopped as soon as the

screw is screwed flush into the material or when the

adjusted torque is reached. The safety clutch is deacti-

vated in the “ ” position, e. g. for drilling.

Select a higher setting or switch to the “ ” symbol

when unscrewing screws.

Gear Selection, Mechanical

f Actuate the gear selector 3 only when the

machine is at a standstill.

Two speed ranges can be preselected with the gear

selector 3.

Gear I:

Low speed range; for screwdriving or working with

large drilling diameter.

Gear II:

High speed range; for working with small drilling diam-

eter.

If the gear selector 3 cannot be pushed through to the

stop, lightly turn the drill chuck with drill.

Switching On and Off

To start the machine, press the On/Off switch 12 and

keep it depressed.

The power light 10 lights up when the On/Off switch

12 is slightly depressed, and enables illumination of the

screwing location in unfavourable light conditions.

To switch off the machine, release the On/Off switch

12.

Adjusting the Speed

The speed of the switched on power tool can be varia-

bly adjusted, depending on how far the On/Off switch

12 is pressed.

Light pressure on the On/Off switch 12 results in a low

rotational speed. Further pressure on the switch results

in an increase in speed.

Fully automatic spindle locking (Auto-lock)

When the On/Off switch 12 is not pressed, the drill

spindle and thus the tool holder are locked.

This enables screws to be screwed in, even when the

battery is empty and allows for the machine to be used

as a screwdriver.

Run-on Brake

When the On/Off switch 12 is released, the chuck

brakes to a stop, thus preventing the run-on of the tool.

When driving in screws, wait until the screw is screwed

in flush with the material and then release the On/Off

switch 12. By doing so, the head of the screw does not

penetrate into the material.

Operating Instructions

f Apply the power tool to the screw only when

it is switched off. Rotating tool inserts can slip off.

Soft Grip

The gripping surface (soft grip) 6 reduces the danger

of slipping and thereby improves the grip on the

machine and the handling.

At the same time, the rubber coating achieves a vibra-

tion-reducing effect.

Tips

After longer periods of working at low speed, allow the

machine to cool down by running it for approx.

3 minutes at maximum speed with no load.

For drilling in metal, use only perfectly sharpened HSS

drill bits (HSS=high-speed steel). The appropriate

quality is guaranteed by the Bosch accessories pro-

gram.

Before screwing larger, longer screws into hard mate-

rials, it is advisable to predrill a pilot hole with the core

diameter of the thread to approx.

of the screw

length.

Maintenance and Service

Maintenance and Cleaning

f Before any work on the machine (e. g., main-

tenance, tool change, etc.) as well as during

transport and storage, set the rotational

direction switch to the centre position. Unin-

tentional actuation of the On/Off switch can lead to

injuries.

f For safe and proper working, always keep the

machine and ventilation slots clean.

If the machine should fail despite the care taken in man-

ufacturing and testing procedures, repair should be

carried out by an after-sales service centre for Bosch

power tools.

In all correspondence and spare parts order, please

always include the 10-digit article number given on the

type plate of the machine.

OBJ_BUCH-213-001.book Page 16 Wednesday, October 11, 2006 8:37 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch PSR12-2 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info