Bedienungsanleitung Bosch PSS250AE (Seite 12 von 62) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

473385

Zoom out

Zoom in

Vorherige Seite

1/62

Nächste Seite

12 | English

2 609 004 199 | (30.8.11) Bosch Power Tools

Robert Bosch GmbH, Power Tools Division

D-70745 Leinfelden-Echterdingen

01.09.2011

Assembly

f Before any work on the machine itself, pull the mains

plug.

Replacing the Sanding Sheet

When attaching a new sanding sheet, remove any dust or de-

bris from the sanding plate 5 (e. g. with a brush).

To ensure optimum dust extraction, pay attention that the

punched holes in the sanding sheet match with the holes in

the sanding plate.

Sanding Sheets with Velcro Backing

(PSS 200 A/PSS 250 AE) (see figure A)

The sanding plate 5 is fitted with Velcro backing for quick and

easy fastening of sanding sheets with Velcro adhesion.

Before attaching the sanding sheet 6, free the Velcro backing

of the sanding plate 5 from any debris by tapping against it in

order to enable optimum adhesion.

Position the sanding sheet 6 flush alongside one edge of the

sanding plate 5, then lay the sanding sheet onto the sanding

plate and press firmly.

To remove the sanding sheet 6, grasp it at one of the tips and

pull it off from the sanding plate 5.

Sanding Sheets without Velcro Backing

(PSS 190 AC/PSS 200 AC/PSS 250 AE) (see figure B)

Lightly lift and unlatch the sanding-sheet clamp 4.

Guide the sanding sheet 6 under the opened rear sanding-

sheet clamp 4 to the stop and clamp the sanding sheet by re-

inserting the sanding-sheet clamp 4.

Fold the sanding sheet 6 firmly around the sanding plate.

Guide the other end of the sanding sheet 6 under the front

sanding-sheet clamp 4 and clamp the sanding sheet by rein-

serting the sanding-sheet clamp 4.

Sanding sheets without holes, e. g. from rolls or by the meter,

can be punctured with the perforating tool 11 for use with

dust extraction. For this, press the machine with the mounted

sanding sheet onto the perforating tool (see figure E).

To remove the sanding sheet 6, unlatch the sanding-sheet

clamp 4 and pull out the sanding sheet.

Selecting the Sanding Sheet

Depending on the material to be worked and the required rate

of material removal, different sanding sheets are available:

Dust/Chip Extraction

f Dusts from materials such as lead-containing coatings,

some wood types, minerals and metal can be harmful to

one’s health. Touching or breathing-in the dusts can cause

allergic reactions and/or lead to respiratory infections of

the user or bystanders.

Certain dusts, such as oak or beech dust, are considered

as carcinogenic, especially in connection with wood-treat-

ment additives (chromate, wood preservative). Materials

containing asbestos may only be worked by specialists.

– As far as possible, use a dust extraction system suita-

ble for the material.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the

materials to be worked.

f Prevent dust accumulation at the workplace. Dusts can

easily ignite.

Integrated Dust Extraction with Dust Box

(see figures C1–C4)

Attach the dust box 3 onto the extraction outlet 8 until it latch-

es.

To empty the dust box 3, pull off the dust box downward.

Before opening the dust box 3, it is recommended to loosen

the dust from the filter element by gently striking it against a

firm support (as shown in the figure).

Grasp the dust box 3 by the recessed grip, fold the filter ele-

ment 9 upward and empty the dust box. Clean the thin plates

of the filter element 9 with a soft brush.

External Dust Extraction (see figure D)

Mount a vacuum hose 10 onto the extraction outlet 8. Con-

nect the vacuum hose 10 with a vacuum cleaner. An overview

for the connection of various vacuum cleaners can be found at

the end of these instructions.

Dr. Egbert Schneider

Senior Vice President

Engineering

Dr. Eckerhard Strötgen

Engineering Director

PT/ESI

Grain size

For the working of all wooden

materials

40—240

For coarse-sanding, e. g. of

rough, unplaned beams and

boards coarse 40, 60

For face sanding and planing

small irregularities medium 80, 100, 120

For finish and fine sanding of hard

woods fine 180, 240

For the working of paint/enam-

el coats or primers and fillers

40—320

For sanding off paint coarse 40, 60

For sanding primer medium 80, 100, 120

For final sanding of primers

before coating fine 180, 240, 320

OBJ_BUCH-60-004.book Page 12 Tuesday, August 30, 2011 8:19 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch PSS250AE Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info