382458
12
Zoom out
Zoom in
Vorherige Seite
1/71
Nächste Seite
English - 4
Unscrew the screw 16 completely. Lift off the
base plate and set it back, so that the screw 16
with the holder 19 can be inserted in the front
notch 18 and screwed into the thread 17.
When tightening the screw 16, the base plate
must be pressed to the rear until it can be felt to
engage.
The cutting angle can not be changed.
The circle cutter/parallel guide 21 as well as
the splinter guard 20 cannot be used in this
case.
To avoid fraying of the surface, install the splinter
guard 20 by pressing it into the base plate 6.
The splinter guard cannot be used for certain saw
blade types (e. g., saw blades with set teeth).
For tight curves, it is best to use a narrow saw
blade.
When sawing metal or similar materials, apply
coolant/lubricant alongside the cutting line.
Circle Cutter / Parallel Guide
(see figures , Accessory)
Maximum thickness of material: 30 mm
Plunge cutting (see figures )
Plunge cuts may only be applied to soft mate-
rials, such as wood, aerated concrete, gyp-
sum plaster boards, etc.!
Place the machine with the front edge of the base
plate on to the workpiece and switch on. Firmly
hold the machine against the workpiece and by
tilting the machine, slowly plunge the saw blade
into the workpiece.
When the base plate fully lays on the surface,
continue sawing along the cutting line.
Before any work on the machine itself, remove
the battery.
For safe and proper working, always keep the
machine and the ventilation slots clean.
In order to avoid operational malfunctions, do
not saw gypsum board from below or over-
head.
To continuously ensure perfect operation of
the machine, the SDS saw blade holder is to
be cleaned regularly. This can be done, e. g.,
by gently striking any dust or debris from the
machine.
The guide roller 8 should occasionally be
checked for wear and lubricated with a drop of oil.
If it is worn, it must be replaced.
If the machine should fail despite the care taken
in manufacturing and testing procedures, repair
should be carried out by an after-sales service
centre for Bosch power tools.
In all correspondence and spare parts orders,
please always include the 10-digit order number
given on the nameplate of the machine.
Recycle raw materials instead of disposing as
waste.
The machine, accessories and packaging should
be sorted for environmental-friendly recycling.
These instructions are printed on recycled paper
manufactured without chlorine.
The plastic components are labelled for catego-
rized recycling.
Offsetting the Foot Plate
(see figure )
Splinter Guard (see figure )
Tips
C
D
E F
G H
Maintenance and Cleaning
Environmental Protection
12 • 2 609 932 131 • 02.03
12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Bosch pst 14 4 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info