Bedienungsanleitung Bosch PST Universal (Seite 15 von 191) (Alle Sprachen)

634130

Zoom out

Zoom in

Vorherige Seite

1/191

Nächste Seite

English | 15

Bosch Power Tools 1 609 92A 1PS | (20.1.16)

Technical file (2006/42/EC) at:

Robert Bosch Power Tools GmbH, PT/ETM9,

70538 Stuttgart, GERMANY

Robert Bosch Power Tools GmbH

70538 Stuttgart, GERMANY

Stuttgart, 01.01.2017

Assembly

 Before any work on the machine itself, pull the mains

plug.

Replacing/Inserting the Saw Blade

 When mounting the saw blade, wear protective gloves.

Danger of injury when touching the saw blade.

Selecting a Saw Blade

An overview of recommended saw blades can be found at the

end of these instructions. Use only T-shank saw blades or saw

blades with 1/4" universal shank (U-shank). The saw blade

should not be longer than required for the intended cut.

Use a thin saw blade for narrow curve cuts.

Inserting the Saw Blade (see figure A1)

 Clean the shank of the saw blade before inserting it. An

unclean shank cannot be fastened securely.

If required, remove the dust cover 9 (see “Dust Cover”).

Push the saw blade holder 13 upward in the direction of the

arrow. Insert the saw blade 15 (teeth in cutting direction) to

the stop into the saw blade holder.

While inserting the saw blade, pay attention that the back

of the saw blade is positioned in the groove of the guide

roller 14.

 Check the tight seating of the saw blade. A loose saw

blade can fall out and lead to injuries.

Removing the Saw Blade (see figure A2)

Push the saw blade holder 13 upward in the direction of the

arrow and remove the saw blade 15.

If the saw blade is wedged or jammed when removing, set ad-

justing lever 7 to maximum orbital action and press the saw

blade holder 13 lightly toward the front (max. 2 mm).

Saw Blade Storage (see figure B) (PST Universal

)

Up to six saw blades with lengths to 110 mm can be stored in

the saw blade storage 5. Insert the saw blades with the T-shank

into the recess of the saw blade storage intended for this. Up to

three saw blades can be placed on top of each other.

Shut the saw blade storage and slide it to the stop into the

opening of the base plate 6.

Splinter Guard (see figure C)

The splinter guard 16 (accessory) can prevent fraying of the

surface while sawing wood. The splinter guard can only be

used for certain saw blade types and only for cutting angles of

0°. When sawing with the splinter guard, the base plate 6

must not be moved back for cuts that are close to the edge.

Press the splinter guard 16 from the bottom into the base

plate 6.

“Cut Control” (PST Universal

)

“Cut Control” enables precise guiding of the power tool along

a cutting line marked on the workpiece. The “Cut Control” kit

includes the viewing window 11 with cutting marks and the

base 10 for attachment to the power tool.

Attaching “Cut Control” to the Base Plate (see figure D)

Clamp the “Cut Control viewing window ” 11 into the holders

of Cut Control base 10. Then, lightly press the base together

and allow it to engage into the accessory holder 17 of the base

plate.

Dust/Chip Extraction

 Dusts from materials such as lead-containing coatings,

some wood types, minerals and metal can be harmful to

one’s health. Touching or breathing-in the dusts can cause

allergic reactions and/or lead to respiratory infections of

the user or bystanders.

Certain dusts, such as oak or beech dust, are considered

as carcinogenic, especially in connection with wood-treat-

ment additives (chromate, wood preservative). Materials

containing asbestos may only be worked by specialists.

–As far as possible, use a dust extraction system suitable

for the material.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the

materials to be worked.

 Prevent dust accumulation at the workplace. Dusts can

easily ignite.

Dust Cover (see figures E–F) (PST Universal

)

Mount the dust cover 9 before connecting the machine to the

dust extraction.

Mount the dust cover 9 onto the machine in such a manner

that the centre holder engages on the contact protector 18

and the two outer holders engage in the openings on the cas-

ing.

Remove the dust cover 9 for applications without dust extrac-

tion as well as when performing mitre cuts. For this, push the

dust cover together at the two outer holders and pull it off to-

ward the front.

Connecting the Dust Extraction

Place a vacuum hose 3 (accessory) onto the vacuum connec-

tion 4. Connect the vacuum hose 3 with a vacuum cleaner (ac-

cessory). An overview for the connection of various vacuum

cleaners can be found at the end of these instructions.

Switch the saw dust blower off when a dust extraction system

is connected (see “Sawdust Blower Device”).

Henk Becker

Executive Vice President

Engineering

Helmut Heinzelmann

Head of Product Certification

PT/ETM9

OBJ_BUCH-2499-003.book Page 15 Wednesday, January 20, 2016 9:27 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch PST Universal Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info