Bedienungsanleitung Bosch PTA 2400 (Seite 13 von 91) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

544042

Zoom out

Zoom in

Vorherige Seite

1/91

Nächste Seite

English | 13

Bosch Power Tools 1 609 929 T64 | (17.6.11)

Together with the power tool, the saw stand is intended for

the cutting to length of boards and profiles.

Product Features

The numbering of the product features refers to the illustra-

tion of the saw stand on the graphics pages.

1 Attachment set

2 Retaining adapter

3 Locking pin of the saw stand legs

4 Height-adjustable leg

5 Locking knob of the attachment set 1

6 Material stop

7 Locking knob of the length stop 6

8 Workpiece support

9 Locking knob of the workpiece support 8

10 Table extension

11 Locking pin of the table extension 10

12 Fastening kit, retaining adapter

13 Fastening kit, power tool

14 Lock nut

15 Fastening hole

16 Assembly-sliding plate

17 Locking knob of the table extension 10

18 Adjustment screw of the attachment set 1

Accessories shown or described are not part of the standard deliv-

ery scope of the product. A complete overview of accessories can

be found in our accessories program.

Technical Data

Assembly

Delivery Scope

Please also observe the representation of

the delivery scope at the beginning of the op-

erating instructions.

Before assembling the saw stand, check if all

parts listed below are provided:

Additionally required tools (not in delivery scope):

– Phillips screwdriver

– Spanner

Assembling the Saw Stand

– Carefully remove all parts included in the delivery from

their packaging.

– Remove all packaging material.

Setting Up the Saw Stand (see figures A1 – A2)

– Lay the saw stand upside down on the floor (legs facing up-

ward).

– Push the locking pin 3 in and tilt the leg upward until the

locking pin can be heard to engage.

– Repeat this workstep with the other three legs.

– Turn around the saw stand to the working position.

The manufacturer logo must face toward the front so that it

can be read.

– Ensure that the saw stand is stable and that all locking pins

have engaged.

The saw stand is easily aligned with the height-adjustable leg

– Loosen lock nut 14 and screw the leg in or out until the saw

stand is aligned level and all four legs face against the floor.

Saw stand PTA 2400

Article number

3 603 M05 0..

Length of saw stand without

table extension

mm 1220

Length of saw stand with table

extension

mm 2440

Height of saw stand

mm 820

Max. carrying capacity

(power tool + workpiece)

without table extension

– Attachment set

kg 160

Max. carrying capacity

(power tool + workpiece)

with table extension

– Attachment set

– Per table extension

110

Weight according to

EPTA-Procedure 01/2003 kg 20.4

No. Designation Quantity

Saw stand PTA 2400 1

Attachment set

Locking knob of the attachment set

Retaining adapter 2

Retaining adapter fastening kit

consisting of:

– Assembly-sliding plate

– Hexagon bolt (M8 x 15)

–Washer

Workpiece support 2

Length stop

Locking knob of the length stop

Carriage bolt (M6 x 46)

Power tool fastening kit

consisting of:

– Hexagon bolt (M8 x 50)

–Washer

–Wing nut

OBJ_BUCH-940-003.book Page 13 Friday, June 17, 2011 3:22 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch PTA 2400 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info