Bedienungsanleitung Bosch PVQ811F15E (Seite 13 von 36) (Englisch)

745998

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

en Operating modes

ÇOperating modes

Oper at i ng modes

This appliance can be used in air extraction mode or

circulating-air mode.

Exhaust air mode

Note: The exhaust air must not be conveyed into a

functioning smoke or exhaust gas flue or into a shaft

which is used to ventilate installation rooms which

contain heat-producing appliances.

■Before conveying the exhaust air into a non-

functioning smoke or exhaust gas flue, obtain the

consent of the heating engineer responsible.

■If the exhaust air is conveyed through the outer wall,

a telescopic wall box should be used.

Circulating-air mode

Note: To bind odours in circulating-air mode, you must

install an activated carbon filter. The different options for

operating the appliance in circulating-air mode can be

found in the brochure. Alternatively, ask your dealer.

The required accessories are available from specialist

outlets, from customer service or from the Online Shop.

KBefore using for the first

time

Bef or e usi ng f or t he f i r st time

Please read the following information before using the

appliance for the first time:

Clean the appliance and all accessory parts thoroughly.

Before you can use your new appliance, you must apply

certain settings.

Switch the hob on and off using the main switch #.

Setting the operating mode

The appliance is supplied with a preset air recirculation

mode.

When the hob is installed with an air outlet to the

outside, you must configure the setting ™‚ˆ in this

mode. See section ~ "Basic settings".

The air which is drawn in is cleaned

by the grease filters and conveyed to

the exterior by a pipe system.

The air which is drawn in is cleaned by the

grease filters and an activated carbon filter

and conveyed back into the kitchen.

Operating the appliance en

1Operating the appliance

Oper at i ng t he appl i ance

This chapter explains how to set a hotplate. The table

shows heat settings and cooking times for various

meals.

Tip: Switch on the ventilation system when you start

cooking and only switch it off a few minutes after you

have finished cooking. This is the most effective way to

remove the cooking vapours.

Note: Never operate the appliance without the metal

grease filter and the overflow container.

Switching the hob on and off

The main switch is used to switch the hob on and off.

To switch on: Touch the # symbol. An audible signal

sounds. The indicator next to the main switch and the

hotplate indicators ‹ light up. The hob is ready to use.

To switch off: Touch the # symbol until the indicator

goes out. All hotplates are switched off. The residual

heat indicator remains lit until the hotplates have cooled

down sufficiently.

Notes

■The hob switches off automatically if all hotplates

have been switched off for more than 20 seconds.

■The selected settings are stored for four seconds

after the hob has been switched off. If you switch it

on again during this time, the hob will operate using

the previously stored settings.

Setting a hotplate

Set the required heat setting using symbols ò to ê.

Heat setting ò = lowest setting.

Heat setting ê = highest setting.

Every heat setting has an intermediate setting. This

intermediate setting is marked in the control panel with

the Ø symbol.

Notes

■To protect the fragile parts of your appliance from

overheating and electrical overloading, the hob may

temporarily reduce the power.

■In order to prevent the appliance from producing

excess noise, the hob may temporarily reduce the

power.

Selecting a hotplate and heat setting

The hob must be switched on.

1. Touch the ø symbol for the required hotplate.

The ‹ symbol lights up and the ¬ symbol

underneath.

2. Then select the required heat setting from the

settings range.

The heat setting is set.

Changing the heat setting

Select the hotplate and then set the required heat

setting in the control panel.

Switch off the hotplate

Select the hotplate and set it to ‹ in the programming

panel. The hotplate turns off and the residual heat

indicator appears.

Notes

■If no pan has been placed on the hotplate, the

selected power level flashes. After a certain time has

elapsed, the hotplate switches off.

■If a pan has been placed on the hotplate before

switching on the hob, it will be detected within

20 seconds of pressing the main switch and the

hotplate will be selected automatically. Once

detected, select the power level within the next

20 seconds or the hotplate will switch off.

If more than one pan is placed on the hob, only one

will be detected when switching it on.

 

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch PVQ811F15E Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bosch PVQ811F15E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info