Bedienungsanleitung Bosch PWS 1500 (Seite 14 von 28) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

543996

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

English | 15

Bosch Power Tools 1 609 929 R38 | (26.6.08)

The machine must al-

ways work in an up-

grinding motion.

Otherwise, the dan-

ger exists of it being

pushed uncontrolled

out of the cut.

When cutting pro-

files and square bar,

it is best to start at

the smallest cross

section.

Cutting Stone

f For cutting stone, always work with the cut-

ting guide with dust extraction protection

guard 19.

f The machine may be used only for dry cut-

ting/grinding.

For cutting stone, it is best to use a diamond cut-

ting disc. As a safety measure against jamming,

the cutting guide with dust extraction protection

guard 19 must be used.

Operate the machine only with dust extraction

and additionally wear a dust protection mask.

The vacuum cleaner must be approved for the ex-

traction of masonry dust. Bosch provides suita-

ble vacuum cleaners.

Switch on the ma-

chine and place the

front part of the cut-

ting guide on the

workpiece. Slide

the machine with

moderate feed,

adapted to the ma-

terial to be worked.

For cutting expecially hard material, e. g., con-

crete with high pebble content, the diamond cut-

ting disc can overheat and become damaged as a

result. This is clearly indicated by circular spark-

ing, rotating with the diamond cutting disc.

In this case, interrupt the cutting process and al-

low the diamond cutting disc to cool by running

the machine for a short time at maximum speed

with no load.

Noticeable decreasing work progress and circu-

lar sparking are indications of a diamond cutting

disc that has become dull. Briefly cutting into

abrasive material (e. g. lime-sand brick) can re-

sharpen the disc again.

Information on Structures

Slots in structural walls are subject to the Stand-

ard DIN 1053 Part 1, or country-specific regula-

tions.

These regulations are to be observed under all

circumstances. Before beginning work, consult

the responsible structural engineer, architect or

the construction supervisor.

Maintenance and Service

Maintenance and Cleaning

f Before any work on the machine itself, pull

the mains plug.

f For safe and proper working, always keep

the machine and ventilation slots clean.

f In extreme working conditions, conductive

dust can accumulate in the interior of the

machine when working with metal. The pro-

tective insulation of the machine can be de-

graded. The use of a stationary extraction

system is recommended in such cases as

well as frequently blowing out the ventila-

tion slots and installing a residual current

device (RCD).

Please store and handle the accessory(-ies) care-

fully.

If the machine should fail despite the care taken

in manufacturing and testing procedures, repair

should be carried out by an after-sales service

centre for Bosch power tools.

In all correspondence and spare parts order,

please always include the 10-digit article number

given on the type plate of the machine.

OBJ_BUCH-758-001.book Page 15 Thursday, June 26, 2008 9:29 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch PWS 1500 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info