Bedienungsanleitung Bosch PWS 1900 (Seite 14 von 111) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

79059

Zoom out

Zoom in

Vorherige Seite

1/111

Nächste Seite

English - 4

■ Before any work on the machine itself, pull

the mains plug.

Use only grinding tools with a permissi-

ble speed at least as high as the no-load

speed of the machine.

Grinding and cutting discs become very

hot while working; do not touch until

they have cooled.

■ Clean the grinder spindle and all parts to be

mounted. For clamping and loosening the

grinding tools, lock the grinder spindle 5 with

the spindle lock button 2.

Actuate the spindle lock button 2 only when

the grinder spindle is at a standstill!

Grinding/Cutting Disc

Pay attention to the dimensions of the grinding

disc. The mounting hole diameter must fit the

mounting flange 9 without play. Do not use re-

ducers or adapters.

When using a diamond cutting disc, take care

that the direction-of-rotation arrow on the dia-

mond cutting disc and the direction of rotation of

the machine (direction-of-rotation arrow on the

machine head) agree.

For mounting, see the illustration page.

Screw on the clamping nut 11 and tighten with

the two-pin spanner (see Section “Quick Clamp-

ing Nut”).

An O-ring (plastic

part) is inserted in

the mounting

flange 9 around the

spigot.

If the O-ring is missing or is damaged, it must

in all cases be replaced (Order No.

1 600 210 039) before the mounting flange 9 is

mounted.

☞

After mounting the grinding tool and be-

fore switching on, check that the grind-

ing tool is correctly mounted and that it

can turn freely.

Flap Disc

Depending on the application, remove the protec-

tion guard 6 and mount the hand guard 18. Place

the special mounting flange 9 (accessory, Order

No. 2 605 703 028) and the flap disc on the

grinder spindle 5. Screw on the clamping nut 11

and tighten with the two-pin spanner.

Rubber Sanding Plate 20

Depending on the application, remove the protec-

tion guard 6 and mount the hand guard 18.

Before mounting the rubber sanding pad 20,

place the 2 spacers 19 onto the grinding spindle.

For mounting, see the illustration page.

Screw on the round nut 22 and tighten with the

two-pin spanner.

Cup Brush 23/Disc Brush

Depending on the application, remove the protec-

tion guard 6 and mount the hand guard 18.

The grinding tool must be able to be screwed

onto the grinding spindle 5 until it rests firmly

against the grinder spindle flange at the end of

the grinder spindle threads. Tighten with an

open-end spanner.

Grinding Cup

When working with grinding cups, use

the special guard 15.

The grinding cup 16 should always protrude

from the guard 15 only as far as absolutely nec-

essary for the work to be performed in each case.

Adjust the guard 15 to this distance.

For mounting, see the illustration page.

Screw on the clamping nut 11 and tighten with

the fitting offset two-pin spanner 17.

Mounting the Grinding Tools

1 609 929 R44 - Buch Seite 4 Dienstag, 11. März 2008 2:06 14

14 • 1 609 929 R44 • 05.01

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch PWS 1900 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bosch PWS 1900

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info