Bedienungsanleitung Bosch PWS 850-125 (Seite 24 von 145) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

544006

Zoom out

Zoom in

Vorherige Seite

1/145

Nächste Seite

24 | English

1 609 92A 1ZT | (17.5.16) Bosch Power Tools

Rotating the Machine Head

Only for power tools with the article number

3 603 CA2 0..:

 Before any work on the machine itself, pull the mains

plug.

The machine head can be turned by 180°. This allows you to

set the On/Off switch to a more favourable handling position

for special jobs, e. g., for left-handers.

– Remove the screw at securing device 20 of release lever 1

(see Fig. A).

– Completely unscrew the 4 screws (see Fig. B). Carefully

turn the machine head to the new position without remov-

ing it from the housing. Mount and tighten the 4 screws

again.

– Screw the securing device 20 of release lever 1 back onto

the machine head (see Fig. C).

Observe the instructions under “Mounting the Protective De-

vices”. The protection guard may only be turned while actuat-

ing the release lever 1.

Dust/Chip Extraction

 Dust from materials such as lead-containing coatings,

some wood types, minerals and metal can be harmful to

one’s health. Touching or breathing-in the dust can cause

allergic reactions and/or lead to respiratory infections of

the user or bystanders.

Certain dust, such as oak or beech dust, is considered car-

cinogenic, especially in connection with wood-treatment

additives (chromate, wood preservative). Materials con-

taining asbestos may only be worked by specialists.

– As far as possible, use a dust extraction system suitable

for the material.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the

materials to be worked.

 Prevent dust accumulation at the workplace. Dust can

easily ignite.

Operation

Starting Operation

 Observe correct mains voltage! The voltage of the pow-

er source must agree with the voltage specified on the

nameplate of the machine. Power tools marked with

230 V can also be operated with 220 V.

When operating the machine with power from mobile genera-

tors that do not have sufficient reserve capacity or are not

equipped with suitable voltage control with starting current

amplification, loss of performance or untypical behavior can

occur upon switching on.

Please observe the suitability of the power generator being

used, particularly with regard to the mains voltage and fre-

quency.

Switching On and Off

To start the power tool, push the On/Off switch 3 forwards.

To lock the On/Off switch 3, press the On/Off switch 3 down

at the front until it latches.

To switch off the power tool, release the On/Off switch 3 or,

if it is locked, briefly push down the back of the On/Off switch

3 and then release it.

To save energy, only switch the power tool on when using it.

 Check grinding tools before using. The grinding tool

must be mounted properly and be able to move freely.

Carry out a test run for at least one minute with no load.

Do not use damaged, out-of-centre or vibrating grind-

ing tools. Damaged grinding tools can burst and cause in-

juries.

Restarting Protection

The restarting protection feature prevents uncontrolled re-

starting of the machine after an interruption in the power sup-

ply.

To restart the operation, switch the On/Off switch 3 to the

Off position and start the machine again.

Working Advice

 Exercise caution when cutting slots in structural walls;

see Section “Information on Structures”.

 Clamp the workpiece if it does not remain stationary

due to its own weight.

 Do not strain the machine so heavily that it comes to a

standstill.

 After heavily straining the power tool, continue to run

it at no-load for several minutes to cool down the acces-

sory.

 Do not touch grinding and cutting discs before they

have cooled down. The discs can become very hot while

working.

 Do not use the power tool with a cut-off stand.

max.

[mm]

D b d [min

-1

] [m/s]

115

125

22.2

11000

115

125

–

11000

75 30 M 14 11000 45

OBJ_BUCH-1824-005.book Page 24 Tuesday, May 17, 2016 8:55 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch PWS 850-125 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bosch PWS 850-125

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info