Bedienungsanleitung Bosch PWS750-125 (Seite 19 von 117) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

473393

Zoom out

Zoom in

Vorherige Seite

1/117

Nächste Seite

English | 19

Bosch Power Tools 2 609 005 556 | (23.9.11)

Cutting Guide with Dust Extraction Protection Guard

The cutting guide with dust extraction protection guard 17 is

mounted in the same manner as the protection guard for

grinding 6.

Auxiliary Handle

f Operate your machine only with the auxiliary handle 4.

Screw the auxiliary handle 4 on the right or left of the machine

head depending on the working method.

Hand Guard

f For operations with the rubber sanding plate 13 or with

the cup brush/wheel brush/flap disc, always mount the

hand guard 12.

The hand guard 12 is fastened with the auxiliary handle 4.

Mounting the Grinding Tools

f Before any work on the machine itself, pull the mains

plug.

f Grinding and cutting discs become very hot while

working; do not touch until they have cooled.

Clean the grinder spindle 5 and all parts to be mounted.

For clamping and loosening the grinding tools, lock the grind-

er spindle with the spindle lock button 2.

f Actuate the spindle lock button only when the grinder

spindle is at a standstill. Otherwise, the machine may be-

come damaged.

Grinding/Cutting Disc

Pay attention to the dimensions of the grinding tools. The

mounting hole diameter must fit the mounting flange without

play. Do not use reducers or adapters.

When using diamond cutting discs, pay attention that the di-

rection-of-rotation arrow on the diamond cutting disc and the

direction of rotation of the machine (see direction-of-rotation

arrow on the machine head) agree.

See graphics page for the mounting sequence.

To fasten the grinding/cutting disc, screw on the clamping nut

9 and tighten with the two-hole spanner.

f After mounting the grinding tool and before switching

on, check that the grinding tool is correctly mounted

and that it can turn freely. Make sure that the grinding

tool does not graze against the protection guard or oth-

er parts.

Flap Disc

f For operations with the flap disc, always mount the

hand guard 12.

Rubber Sanding Plate

f For operations with the rubber sanding plate 13, al-

ways mount the hand guard 12.

See graphics page for the mounting sequence.

Screw on the round nut 15 and tighten with the two-pin span-

ner.

Cup Brush/Disc Brush

f For operations with the cup brush/wheel brush, always

mount the hand guard 12.

See graphics page for the mounting sequence.

The cup brush/disc brush must be able to be screwed onto

the grinder spindle until it rests firmly against the grinder

spindle flange at the end of the grinder spindle threads. Tight-

en the cup brush/disc brush with an open-end spanner.

Approved Grinding Tools

All grinding tools mentioned in these operating instructions

can be used.

The permissible speed [min

-1

] or the circumferential speed

[m/s] of the grinding tools used must at least match the values

given in the table.

Therefore, observe the permissible rotational/circumferen-

tial speed on the label of the grinding tool.

Dust/Chip Extraction

f Dusts from materials such as lead-containing coatings,

some wood types, minerals and metal can be harmful to

one’s health. Touching or breathing-in the dusts can cause

allergic reactions and/or lead to respiratory infections of

the user or bystanders.

Certain dusts, such as oak or beech dust, are considered

as carcinogenic, especially in connection with wood-treat-

ment additives (chromate, wood preservative). Materials

containing asbestos may only be worked by specialists.

– As far as possible, use a dust extraction system suita-

ble for the material.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the

materials to be worked.

f Prevent dust accumulation at the workplace. Dusts can

easily ignite.

Operation

Starting Operation

f Observe correct mains voltage! The voltage of the pow-

er source must agree with the voltage specified on the

nameplate of the machine. Power tools marked with

230 V can also be operated with 220 V.

max.

[mm]

D b d [min

-1

] [m/s]

115

125

22.2

11000

115

125

–

11000

75 30 M 14 11000 45

OBJ_DOKU-28019-001.fm Page 19 Friday, September 23, 2011 8:28 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch PWS750-125 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info