746081

Bosch PXX895D66E Seite 59

59
Zoom out
Zoom in
Vorherige Seite
1/64
Nächste Seite
en Trouble shooting
58
3Trouble shooting
Tr oubl e s hoot i ng
Usually, faults are small matters that are easy to
eliminate. Please read the information in the table
before calling the after-sales service.
Display Possible cause Solution
None The power supply has been disconnected. Use other electrical appliances to check whether the power sup-
ply has been interrupted.
The appliance has not been connected as shown
in the circuit diagram.
Ensure that the appliance has been connected as shown in the
circuit diagram.
Electronics fault. If the fault cannot be rectified, inform the technical after-sales ser-
vice.
The displays flash. The control panel is damp or there is something
on it.
Dry the control panel or remove the object.
The Ù display flashes in the
cooking zone displays.
A fault has occurred in the electronics. To acknowledge the fault, briefly cover the control panel with
your hand.
”The activated charcoal filter is saturated or the
saturation indicator lights up even though the fil-
ter has been cleaned or replaced.
Change the filter and reset the filter saturation indicator. You can
find additional information about this in the section entitled
~ "Cleaning".
”ƒ / “‰ƒ‹ˆ / “ˆ‹‚† The electronics have overheated and have
switched off the affected cooking zone.
Wait until the electronics have cooled down sufficiently. Then
touch any symbol on the hob.
”… / “‰ƒ‹‰ / “ˆ‹‚† The electronics have overheated and all of the
cooking zones have been switched off.
Ӡ + power level and audible
signal
There is hot cookware near the control panel.
There is a risk that the electronics will overheat.
Remove the cookware that is causing the problem. The fault code
goes out shortly afterwards. You can continue cooking.
Ӡ and audible signal There is hot cookware near the control panel.
The cooking zone has been switched off to pro-
tect the electronics.
Remove the cookware that is causing the problem. Wait a few
seconds. Touch any touch control. When the fault indicator goes
out, you can continue cooking.
”‚ / ”‡ The cooking zone has overheated and has been
switched off to protect the work surface.
Wait until the electronics have cooled down sufficiently. Then
switch the cooking zone on again.
”‹ The transfer settings function cannot be acti-
vated.
Confirm the fault display by touching any sensor. You can cook
without using the settings transfer function. Contact our technical
after-sales service.
”‰ The cooking zone has been operating continu-
ously for an extended period.
The automatic safety cut-out function has been activated. You can
find additional information about this in the section entitled .
“ˆ‹‚‹ The hob is unable to connect to your home net-
work.
Confirm the fault display by touching any sensor. You can cook
without the connection.
If the message appears again, contact our technical after-sales
service.
“‰ƒ‹ƒ The cooking sensor has overheated and the
cooking zone has been switched off.
Wait until the cooking sensor has cooled down sufficiently before
activating the function again.
“‰ƒ‹„ The cooking sensor has overheated and all of
the cooking zones have been switched off.
If you are not using the cooking sensor, remove it from the cook-
ware and keep it away from other cooking zones or heat sources.
Switch on the cooking zones.
“‰ƒ‹… The battery in the cooking sensor is almost flat. Replace the 3 V CR2032 battery. For more information, see the
section entitled ~ "Changing the battery".
“‰ƒ‹† The connection to the cooking sensor has been
broken.
Switch the function off and then on again.
“‰ƒ‹‡ The cooking sensor is broken/faulty. Contact our technical after-sales service.
Do not place hot cookware on the control panel.
Trouble shooting en
59
Notes
■If “ appears on the display, press and hold the
button for the relevant cooking zone in order to read
the fault code.
■If the fault code is not listed in the table, disconnect
the hob from the mains power supply and wait
30 seconds before reconnecting it. If this code is
displayed again, contact the technical after-sales
service and specify which fault code has appeared.
■If a fault occurs, the appliance will not switch to
standby mode.
The cooking sensor indicator
does not light up.
The cooking sensor is not responding and the
indicator does not light up.
Replace the 3 V CR2032 battery. For more information, see the
section entitled ~ "Changing the battery".
If this does not solve the problem, press and hold the symbol on
the cooking sensor for 8–10 seconds and then reconnect the
cooking sensor to the hob. For more information, see the section
entitled ~ "Connecting the wireless temperature sensor to the
control panel".
If the problem persists, contact our technical after-sales service.
The indicator on the sensor
flashes twice.
The battery in the cooking sensor is almost flat.
You may be interrupted the next time you cook
by the battery running out.
Replace the 3 V CR2032 battery. For more information, see the
section entitled ~ "Changing the battery".
The indicator on the sensor
flashes three times.
The connection to the cooking sensor has been
broken.
Press and hold the symbol on the cooking sensor for 8–10 sec-
onds and then reconnect the cooking sensor to the hob. For more
information, see the section entitled ~ "Connecting the wireless
temperature sensor to the control panel".
“Š‹‹‹
“Š‹‚‹
The operating voltage is incorrect and outside of
the normal operating range.
Contact your electricity supplier.
—…‹‹ The hob is not connected correctly. Disconnect the hob from the mains. Ensure that the hob has been
connected as shown in the circuit diagram.
š“ Demo mode is activated. Disconnect the hob from the mains. Wait for 30 seconds before
reconnecting it. Touch any sensor in the next three minutes.
Demo mode has now been deactivated.
Display Possible cause Solution
Do not place hot cookware on the control panel.
… 59 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

bosch-pxx895d66e

Suche zurücksetzen

  • gutentag ich suche :PXX895D66Ebosch haben sie die?
    gr harald Eingereicht am 22-6-2022 22:48

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Bosch PXX895D66E wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Bosch PXX895D66E

Bosch PXX895D66E Bedienungsanleitung - Deutsch - 64 seiten

Bosch PXX895D66E Bedienungsanleitung - Holländisch - 64 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info