Bedienungsanleitung Bosch RC 2 (Seite 15 von 184) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

544280

Zoom out

Zoom in

Vorherige Seite

1/184

Nächste Seite

English | 15

Bosch Power Tools 1 618 C00 75G | (10.12.12)

to the correct polarity according to the representation on the

inside of the battery lid.

Always replace all batteries at the same time. Only use batter-

ies from one brand and with the identical capacity.

 Remove the batteries from the measuring tool when

not using it for extended periods. When storing for ex-

tended periods, the batteries can corrode and discharge

themselves.

Operation with Battery Pack (see figure C)

 Use only original Bosch lithium ion battery packs with

the voltage listed on the nameplate of your measuring

tool. Using other battery packs can lead to injuries and

pose a fire hazard.

Note: Use of battery packs not suitable for the measuring

tool can lead to malfunctions of or cause damage to the

measuring tool.

Note: The battery pack is supplied partially charged. To en-

sure full capacity of the battery pack, completely charge the

battery pack in the battery charger before using for the first

time.

 Use only the battery chargers listed on the accesso-

ries page. Only these battery chargers are matched to the

lithium ion battery pack that can be used in your measur-

ing tool.

The Lithium-Ion battery pack can be charged at any time with-

out reducing its service life. Interrupting the charging proce-

dure does not damage the battery pack.

The battery pack is equipped with a NTC temperature control

which allows charging only within a temperature range of be-

tween 0 °C and 45 °C. A long battery pack service life is

achieved in this manner.

For installation and removal of the battery pack 23, the meas-

uring tool’s height adjustment must be set to the lowest posi-

tion. For this, turn the thumbwheel for height adjustment 9 in

anticlockwise direction to the stop.

To insert the battery pack 23, press on the latch 6 and fold the

battery lid 7 up. Slide the charged battery pack completely in-

to the battery compartment and close the battery lid.

Operation with 1.5 Ah battery pack: In order to shut the bat-

tery lid 7, the foam damper on the inside of the battery lid

must be removed.

To remove the battery pack 23, press on the latch 6 and fold

the battery lid 7 up. Pull the battery pack out of the battery

compartment.

Battery status Indicator

The three green LEDs of battery status indicator 5 indicate the

charge condition of the batteries or the battery pack 23.

Power Supply of the Remote Control (GSL 2 Set)

Using alkali-manganese batteries is recommended for opera-

tion of the remote control.

To open the battery lid 20, press on the latch 21 and remove

the battery lid. Insert the batteries. When inserting, pay atten-

tion to the correct polarity according to the representation on

the inside of the battery lid.

Always replace all batteries at the same time. Only use batter-

ies from one brand and with the identical capacity.

 Remove the batteries from the remote control when

not using it for longer periods. When storing for longer

periods, the batteries can corrode and discharge them-

selves.

Operation

Starting Operation of the Surface Laser

 Protect the measuring tool against moisture and direct

sun light.

 Do not subject the measuring tool to extreme tempera-

tures or variations in temperature. As an example, do

not leave it in vehicles for long time. In case of large varia-

tions in temperature, allow the measuring tool to adjust to

the ambient temperature before putting it into operation.

In case of extreme temperatures or variations in tempera-

ture, the accuracy of the measuring tool can be impaired.

 Avoid heavy impact to or falling down of the measuring

tool. After severe external impacts, have the levelling ac-

curacy of the measuring tool checked through an author-

ised service agent for Bosch power tools.

 Switch the measuring tool off during transport. When

switching off, the levelling unit, which can be damaged in

case of intense movement, is locked.

Setting Up the Measuring Tool

Set up the measuring tool on the floor surface to be checked,

ensuring that it is firmly positioned.

The levelling accuracy can be influenced through the ambient

temperature. Especially temperature differences occurring

from the ground upward can deflect the laser beam. As the

thermal layering is greatest at ground level, the measuring

tool should always be set up in the centre of the floor surface

to be checked.

Switching On and Off

To switch on the measuring tool, slide the On/Off switch 8 to

the “On” position. Immediately after switching on, the meas-

uring tool sends laser beams out of the exit openings 1.

 Do not direct the laser beam at persons or animals (es-

pecially not at their eye level), and do not stare into the

laser beam yourself (not even from a distance).

To switch off the measuring tool, slide the On/Off switch 8 to

the “Off” position. When switching off, the levelling unit is

locked.

When the measuring tool is not moved or remote-controlled

for approx. 30 minutes, it switches off automatically to save

the batteries or the battery pack.

LED Capacity

Continuous lighting 3 x green  2/3

Continuous lighting 2 x green  1/3

Continuous lighting 1 x green <1/3

Flashing light 1 x green Reserve

OBJ_BUCH-1545-005.book Page 15 Monday, December 10, 2012 11:06 AM

Bosch RC 2 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info