Bedienungsanleitung Bosch Rotak 1400-37 R (Seite 13 von 229) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

591513

Zoom out

Zoom in

Vorherige Seite

1/229

Nächste Seite

English | 13

Bosch Power Tools F 016 L81 153 | (1.7.14)

Electrical Safety

 Warning! Switch off, remove plug

from mains before adjusting,

cleaning or if cable is cut, dam-

aged or entangled.

 The blades continue to rotate for a

few seconds after the machine is

switched off.

 Caution – do not touch the rotat-

ing blade.

Your machine is double insulated for

safety and requires no earth connec-

tion. The operating voltage is 230 V AC,

50 Hz (for non-EU countries 220 V,

240 V as applicable). Only use ap-

proved extension cables. Contact your

Bosch Service Centre for details.

Extension cords/leads should only be

used if they comply with H05VV-F,

H05RN-F types or IEC type design

(60227 IEC 53, 60245 IEC 57).

If you want to use an extension cable

when operating your product, only the

following cable dimensions should be

used:

– 1.0 mm

: max. length 40 m

– 1.5 mm

: max. length 60 m

– 2.5 mm

: max. length 100 m

Note: If an extension cable is used it

must be earthed and connected

through the plug to the earth cable of

your supply network in accordance

with prescribed safety regulations.

If in doubt contact a qualified electrician

or the nearest Bosch Service Centre.

 WARNING! Inadequate extension

cables can be dangerous. Exten-

sion cable, plug and socket must

be of watertight construction and

intended for outdoor use.

Cable connections should be kept dry

and off the ground.

It is recommended for increased elec-

trical safety to use a Residual Current

Device (RCD) with a tripping current of

not more than 30 mA. Always check

your RCD every time you use it.

For products not sold in GB:

WARNING: For your safety, it is re-

quired that the plug attached to the ma-

chine is connected with the extension

cord. The coupling of the extension

cord must be protected against splash

water, be made of rubber or coated

with rubber. The extension cord must

be used with a cable strain relief.

The connection lead must be inspected

for signs of damage at regular intervals

and may only be used if in perfect con-

dition.

If the supply cord is damaged, it must

be replaced by a Bosch Service Centre.

Products sold in GB only: Your prod-

uct is fitted with a BS 1363/A approved

electric plug with internal fuse (ASTA

approved to BS 1362).

If the plug is not suitable for your socket

outlets, it should be cut off and an ap-

propriate plug fitted in its place by an

authorised customer service agent.

The replacement plug should have the

same fuse rating as the original plug.

The severed plug must be disposed of

to avoid a possible shock hazard and

should never be inserted into a mains

socket elsewhere.

Products sold in AUS and NZ only:

Use a residual current device (RCD)

with a rated residual current of 30 mA

or less.

OBJ_BUCH-1919-004.book Page 13 Tuesday, July 1, 2014 9:57 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch Rotak 1400-37 R Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info