Bedienungsanleitung Bosch sgi 53 a 35 eu inox (Seite 70 von 74) (Deutsch, Englisch, Italienisch)

126356

Zoom out

Zoom in

Vorherige Seite

1/74

Nächste Seite

Installation

In order to function correctly the

dishwasher must be properly installed.

Specifications for the water intake and

waste-water drainage, as well as electrical

connections, must fulfil the criteria that are

set out in the following paragraphs and the

installation instructions.

When installing the dishwasher, carry out

tasks in the following order:

– check contents of delivery upon receipt,

– site dishwasher,

– connect drainage hose,

– connect inlet hose to water supply,

– connect dishwasher to electricity supply.

Checking contents of delivery

All functions of your dishwasher have

been thoroughly tested in the factory. A

small number of water marks have been

left on the dishwasher as a result. They

disappear as soon as the appliance is

used for the first time.

Siting the dishwasher

Dimensions associated with siting the

dishwasher are contained in the

installation instructions. Ensure that the

appliance is completely level by adjusting

the feet. Make sure that it is standing on a

firm surface.

Waste water connection

See the installation instructions for the

required connection steps. If required,

attach a siphon with drainage spigot.

Using the enclosed parts, connect the

waste water hose to the drainage spigot

of the siphon.

Ensure that the drainage hose is not

kinked, crushed or twisted (ensure that

there is no sealing cover which prevents

the waster water from flowing away!).

Fresh-water connection

Using the enclosed parts, connect the

fresh water connection to the tap

according to the installation instructions.

Ensure that the fresh water connection is

not kinked, crushed or twisted.

When replacing the appliance, always

connect a new water supply hose to the

water supply. The old supply hose must

not be re-used.

Water pressure:

Minimum 0,5 bar – maximum 10 bar. If the

water pressure is higher, install a pressure

reducing valve.

Flow rate:

Minimum of 10 litres per minute.

Water temperature:

We recommend that you use cold water. If

you do use hot water, the temperature

should not exceed 60 ∞C.

Electrical connection

This appliance should only be connected

to a 230/240 V AC source via a properly

installed earthed socket. See nameplate

32 for size of required fuse.

The socket must be installed close to the

dishwasher.

If you need to extend the mains

connecting lead, do not cut off the plug.

Replace the whole cable, which can be

disconnected at the junction box on the

rear of the appliance.

If the domestic wiring includes a residual-

current-operated (FI) circuit-breaker, make

sure that it bears the mark, as only

this type conforms to the latest regulations

Disconnecting the

dishwasher

Here too, it is important that tasks are

carried out in the correct sequence: always

unplug the appliance from the mains

electricity first of all. Pull plug out of wall

socket. Turn off water supply. Disconnect

drain and water input hoses. Remove

screws in underside of work surface.

Detach base board, if fitted. Pull out

appliance and carefully withdraw hoses at

same time.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch sgi 53 a 35 eu inox Seite 70

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info