Bedienungsanleitung Bosch TA 211E (Seite 11 von 68) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

458026

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

TA 211 E

English

4 Mounting

Before starting work, the voltage supply

(230 V, 50 Hz) to the boiler must be dis-

connected.

4.1 Mounting of the Outdoor Tempera-

ture Sensor AF (Figures and )

The outside temperature sensor AF is intend-

ed for mounting on the surface of an outer

wall.

The following aspects should be observed:

• Between the Northeast and Northwest

sides of the house

• A minimum of 2 m over ground level

• It should not be influenced by windows,

doors, chimneys, direct sunlight or similar

effects (Fig. ).

• In recesses or under balcony and roof over-

hangs are not suitable as mounting loca-

tions (Fig. ).

• If the major occupied rooms of the building

are all located in the same direction, the out-

door sensor can point in that direction.

Notes:

• If the outdoor sensor is mounted on an east

wall, the sensor must be shadowed in the

early morning hours (e. g., by a neighbour-

ing house of a balcony).

Reason: The morning sun disturbs the

heating up of the house after the end of the

reduced night program.

• If the major occupied rooms point in two ad-

jacent directions, mount the outdoor sensor

on the side of the house that has the worst

climatic conditions.

• For the mounting height, the (vertical) cen-

tre of the height heated by the boiler has

proven to the most suitable (H/2 in Fig. ).

To mount, remove the cover (AF

with AF

)

and attach the sensor housing (AF

) with two

screws to the outer wall (Fig. ).

Legend for Figure :

Y/H = Occupied height to be controlled by the

sensor.

= Recommended mounting location

= Alternative mounting location

4.2 Mounting the Regulator (Figures

and )

➀ Pull out the cover (f) at the bottom and re-

move (Fig. ).

➁ Unscrew the screw (g, Fig. ).

➂ Remove the cover (h) forwards.

➃ Pull the blank panel (i) downward and re-

move (Fig. ).

➄ Insert the TA 211 E from below into the

guide rails and slide up until it clicks

(Fig. ).

➅ Insert the plug (k) attached to the regulator

into the intended connector (Fig. ).

4.3 Mounting the Accessories

Mount the time switch, and the mechanical

limiter in accordance with the associated in-

stallation instructions.

5 Electrical Connection

The electrical connection of the regulator has

already been described in Section 4.2.

The following conductor cross sections are to

be used:

Taking the applicable regulations into consid-

eration, the electrical cable used for the con-

nection of the outdoor sensor and the remote

control must be at least type H 05 VV-...

All 24 V lines (measurement current) must be

laid separately from lines carrying 230 V or

400 V so that no inductive effects take place

(Minimum distance 100 mm).

If external inductive influences such as those

caused by power cables, tram lines, trans-

former stations, radio and television equip-

ment, amateur radio stations, microwave

equipment or similar are to be expected,

shielded cable should used for the signal

lines.

3 5

• From TA 211 E to the outdoor sensor:

Length to 20 m 0.75 mm

to 1.5 mm

Length to 30 m 1.0 mm

to 1.5 mm

Length over 30 m 1.5 mm

• From TA 211 E to the remote control

(not in UK): 1.5 mm

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch TA 211E Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info