GUARANTEE TERMS
The
wit
sol
fro
mus
th
Environmental Care
This iron has been designed according to ecological criteria,
related to the sustainable development, analysing its whole
lifecycle
- evaluating the improvement possibilities, from a technical,
economical and environmental point of view.
Before throwing a used appliance away, you should make it
noticeably
to dispose of it in accordance with current laws
Your retailer,
information about these.
This appliance is labelled in accordance with
European
electrical and electronic appliances (waste
electrical and electronic equipment - WEEE).
The guideline determines the framework for
the
throughout the EU.
Important
This
use and must not be used for industrial purposes.
Carefully the
appliance and safeguard them for future reference.
General safety instructions
• iron must not be left unattended while it is
connected to the supply mains.
•
appliance with water or before pouring out the
remaining water after use.
•
surface.
•
on which the stand is placed is stable.
003 TDA36..GB/07/12
Customer Service
Great Britain
Bosch Customer Service
Grand Union House
Old Wolverton Road
Milton Keynes
MK12 5PT
UK +44 (0)844 892 8923
IRL +353 (0)1450 2655
www.bosch-home.co.uk
Operating instructions
Solving Minor Problems Yourself
Problem Possible Causes Solution
Iron does not
work or is not
heating up
Temperature control (J) on a
very low setting
Turn the temperature
control to the desired
position
Connection problems Check that the plug is
inserted into the mains
socket correctly
The automatic shut-off system
(*) has been activated
Move the iron gently from
side to side to re-start it
Iron is not
steaming
There is no water in the tank Fill the water tank
The steam regulator (C) is in the
«0» position
Set the steam regulator
to the relevant position
Scale obstruction of internal
components
Remove the steam
regulator (C) and clean
it. If this does not help
contact an Authorised
Technical Service Centre
Water is dripping
from the holes in
the soleplate
Temperature control (J) setting
is too low
Set the temperature
control within the steam
area (between the “••”
and “max”) or turn the
steam regulator (C) to «0»
You have pressed the shot of
steam button (A) repeatedly
without waiting for 5 seconds
between each press
Wait 5 seconds between
each press of the jet of
steam button
Water has been left in the tank
(G) when the soleplate was
cold, with the steam regulator
(C) set at «1» or «2»
Always empty the tank
after ironing and set the
steam regulator to «0»
after ironing and when
filling the tank
Tap or part distilled water has
not been used (see “Filling the
water tank” section) or other
products such as fragrant water
have been added to the tank
Mix distilled water with
tap water as directed
in the “Filling the water
tank” section and never
add any other products
to the water tank
Deposits come
out through
the holes in the
soleplate
Traces of lime scale are coming
out of the steam chamber
Carry out a cleaning
cycle (see Multiple de-
scaling system section)
Spray does not
work
No water in the tank. Add water to the water
tank.
Obstructed mechanism. Contact an Authorised
Technical Service Centre.
The iron begins
to smoke when
switched on.
During first use: Certain
components on the appliance
have been lightly greased at the
factory and may produce a little
smoke when initially heated.
This is completely normal
and will stop after a short
while.
Flashing lamp on
top of handle (*)
Auto-shut off has been
activated.
Move the iron gently
fromside to side to re-
start it. The lamp (O) will
then flash once before it
re-heats
Thank
has a lightweight design and is built to perform
The
fea
Please visit www.bosch-home.co.uk for more product
information or
to the Online guarantee registration.
Before using the Iron for the first time
Please carry out the following steps:
1
2.
3.
(J)
4.
lamp
by lining it up with the pointer (D).
5.
button
It may
short while.
6
Cleaning and Maintenance
Attention ! Risk of burns !
For general cleaning, follow the information below:
Problem Solution
Dirty/lightly marked iron
body or soleplate
Clean the body of iron or soleplate with a damp
cloth then dry it.
Mark develops on
soleplate during use
Set the iron to its maximum temperature setting.
Rub the iron a few times over with a dry cotton cloth
folded several times.
Heavily stained
soleplate
While the iron is cold, iron a linen cloth soaked in
white vinegar. Then dampen a cloth with water and
wipe the soleplate clean and dry thoroughly.
DO
or
steam function.
DO NOT use a “professional steam cleaner” for cleaning the
ap
D
or
c
TDA 36..
sensixx B2
(*) Model dependent
Yo
•
if
wate
Service Centre before it can be used again.
•
work or repair that the appliance may need, e.g.
replacing a
out by qualified personnel from an Authorised
Technical Service Centre.
•
years
sensory
and
instruction
way and
shall not play
maintenance
supervision.
•
than
down.
• This
the information stated on its characteristics plate.
• This
absolutel
it
• If
will
appl will have to b tak to an a Technic
Service Centre.
• In
phenomena like
can
power Ω
necessary,
for the system impedance at the interface point.
• The
fill the water tank.
• Unplug
if a fault is suspected.
• The
pulling the cable.
• Never immerse the iron in water or any other fluid.
• Do
sun, frost, etc.)
