Using Your Iron
1
max.
A. Shot of steam
O. Auto shut off
indicator lamp (*) N. Power
cable
K. Max. Water
G. Water tank
E. Spray
C. Steam regulator
H. Soleplate
B. Spray button
J. Temperature control
M.
cover
L. Pilot lamp
I. Temperature control pointer
* Model dependent
D. Steam regulator
pointer
F. Metal ironing tip *
2
Set the steam regulator (C) to the «0» position and
unplug the iron from the mains!
Use only
it. will damage
the appliance.
Do
or
normal tap water.
To
water
very hard, mix tap water with distilled water 1:2.
You
supplier.
To
never fill beyond the «max» water level mark (K)!
7
This function enables the iron to be used for dry ironing.
1.
2.
ironed.
8
This can be used to remove stubborn wrinkles.
1.
2. Make sure that there is water in the tank (G).
3. When
out of the spray outlet (E) onto the garment.
9
1.
2.
3.
4.
all the water has come out.
5.
6.
before storing.
7.
10
Thi
features “AntiCalc”.
A. self-clean
Each
cleans the mechanism of any scale deposits.
B. calc’n clean
The
of
weeks, if the water in your area is very hard.
Fill
position and plug in the iron.
After the
over a
posit while pressin
water
might there. When iron stops reassem
steam regula
Heat u
If
the needle tip with vinegar and rinse off with clean water.
C. anti-calc cartridge (model dependent)
The
up of scale produced during steam ironing, helping to extend
the
cannot
11
All the irons in this range are equipped with an anti-drip system.
This
selected temperature setting is too low to prevent water from
dripping
this system is in operation.
Additional Features (Model Dependent)
Auto shut-off “Secure”
Some irons in this range are equipped with an auto-shut off
system.
The “secure” auto shut-off function switches off the iron
automatically
accidents
in,
reach the set temperature.
If
the
on the position the iron has been left in:
Horizontally (flat) or on its side: 30 seconds
Vertically (upright): 8 minutes
The
shut-off has been activated. To switch the
gently from side to side. The light will stop flashing.
Fabric-protection soleplate cover
The fabric-protection cover is used for steam-ironing delicate
garments at maximum temperature without damaging them.
Use of the protector also does away with the need for a cloth
prevent shine on dark materials.
It is advisable to first iron a small section on the inside of the
garment to see if it is suitable.
To attach
in
upward
down on the clip at the rear and remove from the iron.
The protective cover can be purchased from After-sales.
Accessory code
(After-sales)
650808
Metal ironing tip
Th
Tips to help you save energy
St
the energy used, follow the advice below:
• Start
temperature.
• Regulate the steam according to the selected ironing
temperature.
• Only use steam if necessary. If possible, use the spray
function instead.
• Try
the steam
rather
iro
• If the
completely.
• Stand
with the steam regulator on generates wasted steam.
4
The to adjust the amount
steam produced when ironing.
1.
2.
by
Steam will automatically be produced:
Temperature
Setting Steam Regulator
Setting
“to “max ••• 2
•• 1
3.
regulator (C) for a maximum of 2 seconds.
No
to
po
5
This can be used to
in
setting for delicate items.
1.
2.
3.
intervals of 5 seconds.
6
This
curtains
delicate items.
WARNING! Do not use vertical steam while the is
worn. Never spray or aim steam at people or animals!
1.
2.
and the steam regulator (C) to the «2» position.
3.
garment being steamed.
4.
5 seconds,
to allow for continued steam production.
3
The
soleplate (H).
1.
of the garment you are ironing and set the temperature
control (J) to
the pointer (I) on the iron:
Fabric Temperature Setting
Synthetics •
Silk - Wool ••
Cotton - Linen •••
2.
start
accordingly.
temperature for the most delicate material.
3. woollen or synthetic materials iron the reverse side
of
function to prevent stains.
4 your garments based on their care labels, always
starting with clothes that have to be ironed at the lowest
temperature.
5.
out
few seconds after the lamp goes out before you start ironing.
Once
lamp comes on again.
6.
handle
the iron side to side to restart it.
